ETI 56578211 Guia De Inicio Rapido

SURFACE MOUNT DISK LIGHT WITH TWISTFIT MOUNTING SYSTEM
NOTE: Keep your receipt and these instructions for proof of purchase.
WARNING: Shut off the power at the circuit breaker or fuse panel before removing the old fixture,
ballast, or fluorescent tubes.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do
the installation.
INSTALLATION
Can be installed into 5" and 6" housings.
Shut off power at the electrical panel before beginning the installation.
1
Remove fixture and set aside to recycle in accordance with local requirements.
2
NOTICE: Stick the replacement label on the inner wall of the recessed housing before installation.
Choose your favorite correlated color temperature (CCT) before installing the fixture.
3
NOTICE: The factory setting for the correlated color temperature (CCT) is 3000K (56578211/56578311).
B
B
Installing into a recessed can: Attach
4a
the spring clips (not included) to the
fixture.
For surface mounting: Attach the
4b
mounting plate to the J-Box.
WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire, or other injuries which could
be hazardous or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker. • Risk of fire or electric shock. • This product must be
installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. • Risk of fire or electric shock. LED Retrofit Kit
installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. • Risk of fire or electric shock. Install this kit only in luminaires that
have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire. • Do not make or alter
any open holes in an enclosure of wiring or electrical components during kit installation. • To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the
equipment into an outlet on a circuit different from that to which the receiver is connected, and consult the dealer or an experienced radio/TV.
For retrofit kits certified to canadian requirements: the retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction. Product
must be installed by a qualified electrician in accordance with the applicable and appropriate electrical codes. The installation guide does not supersede local or national regulations for electrical installations.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
US Patents - 10,091,855,
10,462,871, 10,492,262
USE AND CARE GUIDE
C
Screw the medium base (E26) socket
5a
adapter (not included) into the socket
in the can.
Make the electrical connections:
5b
• Black wire to black wire.
• White wire to white wire.
• Ground wire to ground.
• Use wire connectors to cover the wire
connections and cover with electrical tape.
Tuck wires inside the electrical box.
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com
Model # 56578211, 56578311, 56578111, 56578411
Part # FMDL-7.5IN-1000LM-8-CP3-SV-TD, FMDL-7.5IN-1500LM-8-CP3-SV-TD,
FMDL-7.5IN-1000LM-8-30K-SV-TD, FMDL-7.5IN-1500LM-8-30K-SV-TD
Certification # 56578211, 56578311, 56578111, 56578411
PACKAGE CONTENTS
Part Description
A Fixture
B Spring Clips*
C Medium Base
(E26) Socket
Adapter*
D Wire Connector
E Mounting Plate
Screw
F Mounting Plate
Hardware not shown to actual size.
* Accessory sold separately - Spring Clips with E26 Adapter
D
Make the electrical connections:
6a
• Black wire to black wire.
• White wire to white wire.
• Ground wire to ground screw.
• Use wire connectors to cover the wire
connections and cover with electrical tape.
Tuck wires inside the electrical box.
Compress the spring clips and insert the fixture
into the can. Make sure the fixture is secure.
Secure the fixture to the mounting
6b
plate by inserting the fixture into
the keyholes on the mounting plate
and twisting the fixture until it is
secure.
Quantity
A
1
2
1
C
3
E
2
1
Model # 95657811101
Restore power at the
7a
electrical panel.
Turn on the light switch to
activate the fixture.
Restore power at the
7b
electrical panel.
Turn on the light switch to
activate the fixture.
B
D
F