Charging Procedure; Charger Mounting - GGP ITALY BT 80 Li 4.0 Manual De Instrucciones

Batería / cargador de baterías
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 45
Li 5.0 were approved by UL according to the
standard IEC 62133: 2012 (Second Edition).
The CB certificate n° DK-34524-UL (for cell
ICR18650HE2).
• Charging only rechargeable Batteries.
• LED turns green blinking during charging, and
green during after charging.
• The disconnection from line voltage is made by
pulling the mains plug.
• The socket outlet must be located close to the
machine and be easily accessible.

CHARGING PROCEDURE

  NOTE    The battery is not shipped fully charged. 
It  is  recommended  to  fully  charge  before  use  to 
ensure  that  maximum run time  can be  achieved. 
This lithium-ion battery will not develop a memory 
and may be charged at any time.
1. Plug the charger (2) into an AC power outlet.
2. Insert the battery pack (1) into the charger (2).
2
This is a diagnostic charger. The Charger
LED Lights will illuminate in specific order to
communicate the current battery status. They are
as follows:
LED STATUS
Blinking Green
Solid Green
Solid Red
Blinking Red
False Defect Note:
When the battery is inserted into the charger,
and thestatus LED flashes, remove the battery
from the chargerfor 1 minute, then reinsert. If the
status LED indicates normal than the battery pack
is good. If the status LED is still blinking, remove
the battery pack and unplug the charger. Wait 1
1
DESCRIPTION
Charging.
Fully Charged
Over Temperature
Charging Fault.
minute and plug the charger back inand reinsert
the battery pack. If the status LED indicates normal
than the battery pack is good. If the status LED is
still blinking then the battery pack is defective and
needs to be replaced.
  NOTE     When  the  red  indictor  flickers,  pull  out 
the  battery  from  the  charger  and  insert  again 
within 2 hours. If the indictor shows charging, that 
means the battery is good. After 2 hours, please 
pull out the battery and also pull out the AC power 
plug of the charger for 1 miniute, and then insert 
the  AC  power  plug  and  the  battery  again.  If  the 
indictor  shows  charging,  that  means  the  battery 
is good. If not, the battery needs to be changed.
Remove the battery from the charger
and pull out the AC power plug.
CHECKING THE CHARGER
If the battery pack does not charge properly:
• Check the current at the power outlet with
another tool. Make sure that the outlet is not
turned off.
• Check that the charger contacts have not been
shorted by debris or foreign material.
• If the surrounding air temperature is not
normal room temperature, move the charger
and battery pack to a location where the
temperature is between 7 ˚C and 40˚C .
If the battery is inserted into the charger
when warm or hot, the CHARGING LED
indicator light on the charger may switch on
and illuminate RED. If this occurs allow the
battery to cool outside of the charger from
approximately 30 minutes.

CHARGER MOUNTING

• This charger can be installed hanging on a wall
using two screws #8 (not supplied).
• Locate the placement for the charger to be wall
mounted.
• If fastening to wood studs use 2 wood screws
(not supplied).
• Drill two holes on center 114.3mm apart
ensuring that they are vertically aligned.
• If fastening to drywall use wall anchors (not
supplied) and screws to secure the charger to
the wall.
  NOTE    If  the  battery  and  the  charger  won't  be 
used  for  a  long  time,  please  remove  the  battery 
from the charger and pull out the AC power plug.
EN - 4

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Bt 80 li 5.0Cgf 80 li

Tabla de contenido