Operating Your Beverage Cooler; Buttons; Setting The Temperature; Features - Gladiator GABC05FDKG Manual De Uso Y Cuidado

A. " " Button
Press this button for 3 seconds to turn off the system. In this
mode, only the LED light will function. Press this button again
to turn the system back on.
B. " " Button
Press Light button to turn the light on and off within Beverage
Cooler compartment. The Beverage Cooler will remain
illuminated for 10 minutes (even when door is closed) when the
light is turned on. When the light is turned off, the Beverage
Cooler compartment will be illuminated when the door is open.
The light will turn off when the door is closed.
C. "Temperature"
Displays the actual temperature inside the Beverage Cooler.
D. "+" Button
Each press of this button will increase the temperature setting
1ºF or 1ºC until it reaches 64ºF (18ºC).
E. "-" Button
Each press of this button will decrease the temperature setting
1ºF or 1ºC until it reaches 37ºF (3ºC).
F. "ºF and ºC unit conversion"
Press "+" & "-" button at the same time and the display will
show "3, 2, 1" countdown, and then the units will convert
between "ºF" and "ºC" or "ºC" and "ºF".

Setting The Temperature

Set the desired cooling temperature by pressing the "+" or
■
"-" buttons. Each press of the buttons will scroll through
the available temperature setting in increments of 1 degree.
The temperature selected will flash in the LED display for
approximately 5 seconds, then revert back to the setting
temperature of the internal cabinet.
The temperature setting can be adjusted from 37ºF (3ºC) to
■
64ºF (18ºC). The factory preset temperature is 54ºF (12ºC).
To view the actual temperature anytime, press and hold one of
■
the "+" or "-" buttons for approximately 5 seconds, and the set
temperature will temporarily flash in the LED display for
5 seconds.
8

OPERATING YOUR BEVERAGE COOLER

A
B
A. Power
B. Light
C. Temperature display

Buttons

C
D
Temperature
E
D. Decrease temperature
E. Increase temperature
When pressing the "+" or "-" buttons, the system will be
■
entering the set up mode. The LED will flash and display the
setting temperature. When exceeding the minimum value
that can be reached, it will stay at the highest adjustable
temperature value.
NOTE: In the event of power interruption or if the unit is
unplugged during setting mode, the set temperature will be
erased, and the system will return to the factory setting
(54ºF (12ºC)).
Recommended temperature range and location when storing
■
wine:
White - 43ºF - 50ºF (6ºC - 10ºC) Upper shelves
Red - 53ºF - 61ºF (12ºC - 16ºC) Lower shelves
Temperature Recollection
■
In the event of a power interruption, the Beverage Cooler will
remember the previous temperature setting, and when the
power is restored, the Beverage Cooler will go back to the
same setting temperature as before the power interruption.
Open Door Alarm
■
When you forget to close the door or the door is not closed
completely, the alarm will sound after 5 minutes. Please close
the door completely to avoid energy loss.
Temperature Alarm
■
If the Beverage Cooler inner temperature is higher than
73ºF (23ºC), "HI" will be displayed and the alarm will sound
continuously. It will inform that the inner temperature is too
high. Please check for the cause. See "Troubleshooting." If the
Beverage Cooler inner temperature is lower than
32ºF (0ºC), "LO/CL" will be displayed and the alarm will sound
continuously. It will inform that the inner temperature is too low.
NOTE: When the Beverage Cooler is first plugged in, after
6 hours if the temperature sensor detects a temperature lower
than 32ºF (0ºC), the alarm will sound, and the display will show
"LO." If the temperature remains lower than 32ºF (0ºC) for 15
additional minutes, the display will change and show "CL." This
"CL" temperature alarm can only be turned off by disconnecting
power.
IMPORTANT:
If the unit is unplugged, power lost, or turned off, you must wait
3 to 5 minutes before the Beverage Cooler will restart. During
this time, the LED display will show the difference in temperature
between the set temperature and the inner temperature.

Features