QualityCraft SOQC935-MBK Manual De Instrucciones página 2

Estufa eléctrica
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

OPERATION:
Controls and switches are located on front panel inside the glass door.
0/|
- Main ON / OFF
- Termostat
750W
- Low heat
Main ON / OFF: Press this button to turn ON the main power of the unit. The indicator
light besides the air exit will turn on.
FLAME ON / OFF: Press this button to turn ON the flame function. The indicator light
will turn on. Adjust the flame Intensity knob for desired flame effect.
750W: For low heat function – press this switch for low heat. The indicator light will
turn on.
1500W: For high heat function - press this switch while the 750W switch is in the "I"
position for high heat. The indicator light will turn on.
THERMOSTAT: To adjust the temperature to your individual requirements. Turn the
thermostat dial to the right (clockwise) to increase the desired temperature and to
the left for lower temperature. This thermostat control dial can only be used while the
750W / 1500W switches are in the "I" position. When the heater reaches the desired
temperature, the heater and 750W / 1500W indicator light will turn off.
Adjust this knob to restart the heater.
FLAME INTENSITY: Turn the dimmer dial clockwise or counter clockwise to get the
desired flame intensity. The dimmer switch can only be used when the FLAME ON /OFF
switch is in the "I" position. Turn this dial to the left end will switch off the flame effect.
THERMOSTAT CONTROL
The heat output is controlled by the thermostat, according to the room temperature.
Set the thermostat dial clockwise to the maximum position initially. When the room
is warm enough, reduce the setting by slowly turning the thermostat dial counter
clockwise until the heater just clicks OFF. This will then maintain the room temperature
at the desired level.
CAUTION: IF YOU USE THIS HEATER IN CONJUNCTION WITH A THERMAL
CONTROL, A PROGRAMMABLE CONTROLLER, A TIMER OR ANY OTHER DEVICE
THAT SWITCHES ON THE HEATER AUTOMATICALLY, REMEMBER TO OBSERVE
ALL SAFETY WARNINGS AT ALL TIMES.
THE STOVE HEATER HAS A SAFETY OVERHEAT PROTECTION. IF THE OVERHEAT
PROTECTION TRIPS, TURN OFF ALL THE SWITCHES AND UNPLUG THE POWER
CORD FROM THE RECEPTACLE. IT SHOULD RESET AUTOMATICALLY AFTER
5 MINUTES.
WARNING: DISCONNECT POWER AND UNPLUG THE POWER CORD BEFORE
ATTEMPTING ANY MAINTENANCE OR CLEANING TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR PERSONAL INJURY. THE BULB(S) IN YOUR UNIT CAN
BECOME EXTREMELY HOT. ALLOW AT LEAST 10 MINUTES BETWEEN TURNING
OFF THE UNIT AND REMOVING THE LIGHT BULBS TO AVOID ACCIDENTAL
BURNING OF THE SKIN.
- Flame Intensity
- Flame ON / OFF
0/|
1500W
- High heat
FLAME EFFECT
The fire effect is created with the use of two, 40 watts B-10 candelabra light bulb with
E12 (small) socket base. The light bulb will have to be replaced from time to time when
they burn out.
During normal operation, the stove heater will always give you simulated flame function. If
the intensity of flame suddenly increases, it means that the light bulb is going to burn out.
Replace the light bulbs immediately, according to the instructions. Do not operate the
stove heater when the light bulb burns out or without the light bulb.
CHANGING THE LIGHT BULB
Unplug the unit and wait until it is cool before any maintenance.
STEP 1: Remove 4 screws on the back of the unit and remove the rear cover.
STEP 2: You will find 2 x 40W Type B-10 Candelabra light bulb with E-12 socket base at
the bottom.
STEP 3: Release the spring holder of light bulbs. Replace the burned out light bulb using
a new 40 watt Type B-10 candelabra light bulb.
STEP 4: Fix the light bulb with spring holder. Replace the rear cover with 4 screws.
STEP 5: Plug in the unit.
CLEANING
To clean unit first turn off controls on unit and unplug unit from power source.
To clean glass door; remove dust with clean dry cloth or to remove finger prints and other
marks clean glass with clean damp cloth. Do not use abrasive cleaners or spray liquids
on glass door surface.
Metal and metal painted parts should be cleaned with damp cloth. Do not use abrasive
cleaners or spray liquid on these surfaces.
STORAGE
When the heater is not in use, the heater shall be stored in dry location and away from
possible damage. The power cord shall be routed properly and avoid from contacting hot/
sharp objects.
2

Publicidad

Tabla de contenido
loading

Tabla de contenido