Publicidad
Idiomas disponibles
Idiomas disponibles
y Use a hammer and a small center punch or nail to mark all 4 of the hole
locations through the template and then remove the tape and template.
y If the charger is being installed onto drywall, you will need to install 4 -
#8 Drywall Anchors (included). Using a 1/4" drill bit, drill 4 holes through
the drywall in the locations of the nail marks. Using a #2 Phillips Head
Screwdriver, install all 4 Drywall Anchors into the drywall until they are
each flush with the surface.
NOTE: If the charger is being installed onto a metal surface, drill 4
appropriately sized holes. The diameter of the drill bit required will
be determined by the type of metal and the thickness of the material.
NOTE: If the charger is being installed onto a wooden surface, drill a
3/32" pilot hole in all 4 locations.
y The mounting screw holes can be accessed from the front of the charger
when the Angle Light is not installed in the charger.
y Looking through the mounting holes in the front face of the charger,
line up the mounting holes for the charger with the pilot holes (or drywall
anchors) and one at a time, carefully insert each of the supplied #8 x 32
x 1 ½" Pan Head Screws into the mounting holes from the front of the
charger. Give each screw a small turn by hand to get each one started.
y Using a #2 Phillips Head Screwdriver, hand-tighten each screw until the
charger is securely affixed to the mounting surface. CAUTION: Do not
use an electric drill or drill driver to install the screws. Do not over-tighten.
Doing so could damage the mounting holes in the charger.
y Plug either the Nightstick AC or DC Power Supply cord into the power
port on the bottom of the 5572-CHGR1 charger and then into the
appropriate power outlet.
y The LED Charge Indicator Light on the charger will momentarily light up
GREEN and then turn RED and then go off. This is normal behavior when
the Angle Light is NOT installed in the charger.
y The charger is now ready to use.
POWERING THE XPR-5572R
The XPR-5572R Intrinsically Safe Permissible Rechargeable Angle
Light can be powered in one of two ways:
y The Nightstick 5572-BATT Lithium-ion Rechargeable Battery Pack.
y The Nightstick 5570-BATT Non-Rechargeable Battery Carrier and 6 - AA
Energizer EN91 or Energizer E91 Batteries.
WARNING: Do not use any other type of non-rechargeable battery with
this light.
WARNING: Do not use rechargeable AA batteries with this light.
5572-BATT LITHIUM-ION RECHARGEABLE BATTERY PACK
WARNING: The Nightstick 5572-BATT Lithium-ion Rechargeable
Battery Pack is a proprietary shape and design and will only fit in
the XPP-5570R or XPR-5572R Angle Lights. Do not attempt to use
this battery pack in any other light. Do not attempt to use any other
rechargeable battery pack in this light.
WARNING: The Nightstick 5572-BATT Lithium-ion Rechargeable
Battery Pack is a sealed unit and is not designed to be opened up. Do
not attempt to open the 5572-BATT Lithium-ion Rechargeable Battery
Pack.
y To install the 5572-BATT Lithium-ion Rechargeable Battery Pack,
Image 1
unscrew the Torx Head Screw located on the Battery Compartment Door
on the base of the light using the included Torx Wrench. (Image 1)
NOTE: The Battery Compartment Door Torx Screw utilizes a design
that prevents the screw from falling out of the door. Do not attempt to
remove the screw. (Image 2)
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.mynightstick.com
Image 2
Image 3
y With the Battery Compartment Door opened enough to provide
clearance, insert the 5572-BATT Lithium-ion Rechargeable Battery Pack
with the end having the metal contacts on it being inserted first and the
rails on the bottom of the Battery Pack positioned toward the back of the
light. (Image 3)
Image 4
5570-BATT NON-RECHARGEABLE BATTERY CARRIER
WARNING: The Nightstick 5570-BATT Non-Rechargeable Battery
Carrier is a proprietary shape and design and will only fit in the XPP-
5570R or XPR-5572R Angle Lights. Do not attempt to use this battery
pack in any other light. Do not attempt to use any other battery pack
in this light.
The Nightstick 5570-BATT Non-Rechargeable Battery Carrier is
designed to fit 6 AA batteries. In order to maintain the XPR-5572R's
Intrinsically Safe Permissible rating, the only AA batteries certified for use
with this light are the Energizer EN91 or Energizer E91.
Do not attempt to use any other brand or model of AA batteries with this
light.
Do not attempt to use any type of rechargeable AA batteries with this
light.
Installing or replacing the batteries
Image 5
y Begin by positioning the 5570-BATT Non-Rechargeable Battery Carrier
with the arrow pointing to the left. (Image 5)
y Using the thumb and index finger, squeeze in on the two sides of the
carrier cover closest to the right end of the carrier. (Image 6)
y This action will cause the tabs on the right end of the cover to release
from the base and allow the cover to simply lift away. (Image 7)
Image 8
y Using 6 – AA Energizer EN91 or Energizer E91 (make sure that all 6
batteries are of one or the other model...do not use a combination of the
two), install the batteries per the diagram located on the inside base of the
battery carrier. (Image 8)
y Take care not to bend any of the battery contact springs, and to make
sure that all 6 batteries are properly seated before reinstalling the cover.
(Image 9)
y To reinstall the cover, insert the two tabs on the left-hand end of the
cover into the two corresponding slots on the left end of base. (Image 10)
INS-XPR5572-15D
With
the
5572-BATT
y
Rechargeable
Battery
Pack
into the handle of the light, close the Battery
Compartment Door and secure it in place with
the Battery Compartment Door Torx Head Screw
and the included Torx Wrench. (Image 4)
WARNING: Do not over-tighten the Battery
Compartment Door Torx Head Screw.
The Angle Light is now ready to be powered
using the Nightstick 5572-BATT Lithium-ion
Rechargeable Battery Pack.
Image 6
Image 9
Lithium-ion
fully
inserted
Image 7
Image 10
Publicidad
