Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

20" High Velocity Floor Fan
Operating Instructions
CONGRATULATIONS ON YOUR PURCHASE OF THE Maxx Air
20" HIGH VELOCITY FLOOR FAN.
With proper care and maintenance the fan will afford you many
years of use. Please read the safety instructions below, and save
for future reference.
THIS FAN IS FOR RESIDENTIAL USE ONLY.
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should
always be followed to reduce the risk of fire, electric shock,
and injury to persons, including the following:
1.
Read all instructions before using the Fan.
2.
Make certain that the power source conforms to the electri-
cal requirements of the Fan.
3.
Use the Fan only as described in these instructions. Any
other use not recommended by the manufacturer may cause fire,
electrical shock or injury to persons.
4.
To reduce the risk of personal injury and electric shock, the
Fan should not be played with or placed where small children can
reach it.
5.
Unplug power cord before installing, servicing or moving the
Fan. Warning: Do not depend upon the on-off switch as the sole
means of disconnecting power when installing or servicing the
fan. Always unplug the power cord.
6.
This Fan must NOT be used in potentially dangerous
locations such as flammable, explosive, chemical-laden or wet
atmospheres.
7.
DO NOT use Fan in or near a window. Rain may create an
electrical hazard.
8.
Completely assemble the Fan according to the assembly
instructions on the reverse of this page before connecting to pow-
er supply. Warning: This appliance has a 3-prong, grounded
plug. If the plug does not fit fully into the outlet, contact a
qualified electrician. Do not attempt to defeat this safety fea-
ture. Warning: this plug is a safety device. To reduce the risk
of fire, shock, and personal injury, do not remove, replace,
repair or tamper with the originally supplied plug. If the fan
does not function properly, it may be duet° the safety device
incorporated in this plug. Call 800-433-1626, Monday-Friday,
between 8:00 a.m. And 5:00 p.m. CST. If the plug warning
label is missing or damaged, call the toll free number for a
replacement label.
9.
Where possible, avoid the use of extension cords. If they
must be used, minimize the risk of overheating by ensuring that
they are UL listed. Never use a single extension cord to operate
more than one Fan. Do not plug the Fan into any other cord-con-
nected device such as a power strip, cord reel, surge protector,
multiple outlet adapters or outlet-type air fresheners. The use of
such devices may create a fire hazard.
10.
Do not operate any Fan with a damaged cord or plug or
VENTAMATIC, LTD. P.O. BOX 728, MINERAL WELLS, TX 76067 • PHONE 800-433-1626 • WWW.BVC.COM
A leader in the ventilation industry for over 60 years, Ventamatic, Ltd. off ers a complete line of air movement products for
commercial, industrial, agricultural, and residential use.
after the Fan malfunctions, has been dropped or damaged in any
manner.
11.
Do not insert or allow fingers or foreign objects to enter any
ventilation or exhaust opening, as it may cause an electric shock,
fire or damage the Fan. Do not block or tamper with the Fan in
any manner while it is in operation.
12.
Always place the Fan on a stable, flat, level surface when
operating to avoid the chance of the Fan overturning. Locate the
Power Cord so the Fan or other objects are not resting on it. Do
not run Power Cord under carpeting. Do not cover Power Cord
with throw rugs, runners, or the like. Arrange Power Cord away
from room traffic and where it will not be tripped over.
13.
This Fan is not intended for use in wet or damp locations.
Never locate a Fan where it may fall into a bathtub or other water
container.
14.
Do not use Fan outdoors.
15.
This Fan is not suitable for use in agricultural facilities
including areas where livestock, poultry or other animals are
confined. Please refer to National Electric Code ( NEC) Article 547-
7 (2008) or applicable state or local codes or standards relating to
electrical requirements for Agricultural Buildings. THIS FAN DOES
NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
16.
This Fan is not suitable for use in hazardous locations.
Please refer to National Electric Code (NEC) Article 500 or
applicable state or local codes or standards relating to electrical
requirements for Hazardous locations. THIS FAN DOES NOT MEET
THE REQUIREMENTS OF NEC ARTICLES 500 (2008).
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK.
DO NOT USE THIS FAN WITH ANY SOLID STATE SPEED CON-
TROL DEVICES.
SAVE THESE INSTRUCTIONS
MODEL: HVFF 20

Publicidad

loading

Resumen de contenidos para Maxx air HVFF 20

  • Página 1 20” High Velocity Floor Fan MODEL: HVFF 20 Operating Instructions CONGRATULATIONS ON YOUR PURCHASE OF THE Maxx Air 20” HIGH VELOCITY FLOOR FAN. With proper care and maintenance the fan will afford you many years of use. Please read the safety instructions below, and save for future reference.
  • Página 2 PLEASE NOTE: The motor bearings in your Maxx Air fan are permanently sealed and DO NOT REQUIRE additional lubrication. If you should have any questions about the operation of your Maxx Air High Velocity Floor Fan, please contact Ventamatic, Ltd. toll free at 1.800.433.1626 VENTAMATIC, LTD.
  • Página 3 ABANICO DE ALTA VELOCIDAD DE PISO MODELO: HVFF 20 DE 20” INSTRUCCIONES DE OPERACIÓN CFELICIDADES EN SU COMPRA DEL ABANICO Maxx Air DE ALTA VELOCIDAD DE PISO DE 20” Con el cuidado y man- ten¬imiento apropiado su abanico le dara muchos años de uso.
  • Página 4 NOTE POR FAVOR: Los cojinetes del motor en su Maxx Air abanico son de sellado permanente y no requieren lubricación adicional. Si usted tiene alguna pregunta con respecto a la operación de su ventilador Maxx Air de piso de alta velocidad, comuniquese con Ventamatic, Ltd. Linea gratis 1.800.433.1626 VENTAMATIC, LTD.