Publicidad
Idiomas disponibles
Idiomas disponibles
1. Introduction:
FA-ART 7W power supply has been exclusively designed to be
used with ART 7W/G2+ monitor (Golmar). Golmar will not be
responsible of the possible damages caused for an improper use
or when used for other purposes than the specified.
Features:
- Universal AC input/full range.
- Multi protection: Short circuit and overload.
- Specific power supply for each ART 7W/G2+ monitor. (Installations
with 2 to 4 apartments).
- DIN 46277 rail mounting.
2. Terminal description:
_
_
+
+
-
-
+
+
12240170 FA-ART 7W
INPUT:100-240V~ 50
OUTPUT:24V
+
N
~100-240V
N: AC input.
L: AC input.
OUTPUT (+): Monitor connection bus terminal.
_
OUTPUT ( ): Door panel connection bus terminal.
3. Installation:
1: Mount the din rail to the wall with wallplugs and screws that
are suplied with power supply.
2: Place the power supply simply pressing it.
DIN rail latch release.
Golmar reserves the right to make any modifications without prior notice.
FA-ART 7W POWER SUPPLY INSTRUCTIONS
24V
/60
HZ 0.8A 28W
±
1.2V
1A
GOLMAR S.A.
C/ Silici, 13
08940 - SPAIN
+
L
N
L
Din rail.
Din rail.
4. Wiring:
Open the AC protection cover:
1. Push the cover bottom towards
the center with your hand.
2. Turn over and pull it out.
3. When the installation and wiring works are finished, place the
protection cover before replacing the electrical current.
Gnd
Connection to monitor
ART 7W/G2+
24Vcc
*
AC Input
100~240Vac
Note:
The installation and handling of this equipment must be
performed by authorised personnel and without the power
connected.
5. Specification:
Input Voltage:
Input Frequency:
Rated Output Voltage:
Rated Output Current:
Working Temperature:
Dimensions:
6. Warning:
-FA-ART 7W power supply has been exclusively designed to be
used with ART 7W/G2+ monitor (Golmar). Golmar will not be
responsible of the possible damages caused for an improper use
or when used for other purposes than the specified.
-The installation and handling of this equipment must be performed
by authorised personnel and without the power connected.
-Install the power supply in a dry and protected place with enough
ventilation, without risk of drip or water projections.
-Install the power supply according to your country rules.
-Do not use excesive force when tightenning the power supply
connector screws.
-The device must be protected by using a thermo-magnetic circuit
*
breaker.
-The power supply must be unplugged from mains during
installation or maintenance progresses.
-To avoid an electrical shock, neither remove the protection cover
nor handle the connected wire in the terminals without first
disconnecting the power supply.
-Do not block ventilation holes of the unit so that air can circulate freely.
-To avoid damage, the power supply has to be firmly fixed.
-Once the power supply has been installed, place the supplied
protection cover on the mains input connector ('N' & 'L').
-Before switching the system on, check that there is no shortcircuit
on the installation.
-In case of system failure, unplug it from mains by using the thermo-
magnetic circuit breaker and contact an authorised Golmar after
sales service.
-This document must be kept together with the device.
Rev.0219
_
+
L
N
100~240Vac
50~60 Hz
±
24
Vdc
1A
-10ºC ~ 40ºC
55*84*54mm
TFA-ART 7W EN Cod. 50124335
1.2V
Publicidad
