Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
'Release' lever
Pouch/Document Entry
CAPABILITIES
Pouch Thickness
Estimated Heat-Up Time
Approximate Cool-Down Time
Lamination Speed
12" (30 cm)/Minute
IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!
• The socket-outlet shall be installed near the equipment and shall be easily accessible.
• To prevent electrical shock, do NOT use laminator close to water and do NOT spill water
on laminator, electric cord, or wall socket.
• Do not leave electric cord in contact with a warm surface.
• Do not leave electric cord hanging from a cupboard or shelf.
• Do not use laminator if electric cord is damaged.
• Do not laminate metal objects.
FEATURES & TIPS
'Release' function
To remove or re-align a pouch during lamination, activate the release
lever located on the back of the machine. The pouch can only be
removed from the entry slot when the lever is activated.
• This machine does not need a carrier to laminate. It is a carrier-free mechanism.
• Always put the item to be laminated into the appropriate sized pouch.
• Always test laminate with a similar size and thickness before final process.
• Prepare pouch and item for lamination. Place item within pouch centered and touch-
ing the leading sealed edge. Ensure the pouch is not too large for the item.
•
If required, trim excess material from around the item after lamination and cooling.
• Always put item in a pouch. Never laminate an empty pouch.
2
407952_RevC_9.5in_Laminator_092614.indd 2-3
Pouch/Document Exit
3-5 mil
Maximum Width
4 Minutes
Voltage
60 Minutes
Frequency
Current (Amps)
• Always supervise children during laminator operation.
• Keep pets away from laminator while in use.
• Switch off and unplug laminator when not in use.
• Do not open or attempt to repair the laminator yourself, as this could result in electric shock and will
void your warranty. Contact Customer Service if you have questions. Please note the warranty does
not apply in cases of abuse, mishandling or unauthorized repair.
Auto Shut Off
Auto
After 30 minutes, the machine will automatically go in to Auto Shut Off
Shut
mode. The Power LED will flash red for 5 minutes and then turn off.
Off
The ready LED will turn off. To continue using the machine press the
ON/OFF switch. The machine will reset itself
• Trim excess pouch material from around your item after laminating and cooling.
• If using both hot and cold lamination in one session, use the cold setting first to avoid
having to wait for the laminator to cool down.
• Before laminating valuable items, do a test run with an item similar in size
and thickness.
• Use a dry-erase marker for writing on laminated pouches.
BEFORE YOU LAMINATE
Select correct
pouch size for
laminated item.
Power Light
(Red)
STEPS FOR HOT LAMINATION
Ready Light
(Green)
1
Power
Switch
Cold/Hot
Switch
Ensure temperature switch on side
of machine is set to hot. Wait for
green light.
9.5" (242 mm)
120V~
STEPS FOR COLD LAMINATION
60 Hz
2.5 A
1
Push temperature switch on side
of machine to cold setting and
wait for green ready light.
TROUBLESHOOTING
Problem
No 'power on' lamp (red LED)
No 'ready' lamp after a long period (green
LED)
The Power LED is flashing red and the Ready
LED (green) has turned off
The ready lamp (green) and the Power LED
(red) have turned off
Pouch is lost in the machine
Jamming
Pouch is damaged after lamination
• Plug laminator into
power outlet.
• Position laminator so you
have enough space to
FPO
allow items to pass freely
through the machine.
2
3
4
Place item inside pouch against
Place pouch, sealed edge first,
To prevent jamming, immediately
into laminator entry. Keep pouch
remove laminated item from back
the sealed edge.
straight and use the entry markings
of machine. Let item cool on flat
as a guide.
surface for several seconds.
CAUTION: Only use self-adhesive pouches when laminating with a cold setting.
2
3
4
Center item on clear side against
Peel a small part of the protective
Place pouch, sealed edge first,
sealed edge; documents cannot
sheet away from document.
into laminator entry. Keep pouch
straight and use the entry mark-
be repositioned once laminated.
ings as a guide. Continue peeling
the protective sheet away.
Possible cause
Solution
Machine not switched on
Switch on machine at the side and at the wall socket
Machine is in a hot or humid area
Move the machine to a cooler and dry area
The laminator has gone in to Auto Shut Off
Press the ON/OFF switch. The machine will reset itself
mode
The laminator is in Auto Shut Off mode
Press the ON/OFF switch. The machine will reset itself
Pouch is jammed
Pouch was used 'open end' first
Pouch was not centered on entry
Press release lever and pull out the item by hand
Pouch was not straight upon entry
Empty pouch was used
Pass cleaning sheets through the machine to test and
Damaged rollers or adhesive on rollers
clean rollers
Switch laminator on (I).
5
To prevent jamming, immediately
remove laminated item from back
of machine.
Need Help?
Customer Service:
US: 1-800-425-0049
3
9/30/14 3:39 PM
Publicidad
