Descargar Imprimir esta página

Hampton Universal Hardware UH40047 Instrucciones De Instalación

Conjunto de perilla/ manija tubular

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

UNIVERSAL
HARDWARE
The Professional's Choice
NEW DOOR PREPARATION
A:
Fold template on edge of door and mark hole for 2-3/8" or 2-3/4" backset.
B:
Drill 2-1/8" hole through door (from both sides to avoid damaging door).
C:
Drill a 1" hole in edge of door.
1
DISASSEMBLE INSIDE KNOB/LEVER & INSIDE ROSE
INSIDE
KNOB/
LEVER
Separate inside assembly.
Insert push pin into hole to
depress catch and remove lever.
4
INSTALL INSIDE ROSE
Align cut with location tab and
push rose until it snaps into place.
©2017 Hampton Products International Corp.
INSTALLATION INSTRUCTIONS FOR TUBULAR KNOBSET/LEVERSET MODELS:
UH40047, UH40048, UH40049, UH40050, UH40051, UH40052, UH40053, UH40054 &
UH40057.
• Fits Doors 1-3/8" to 2" Thick
2-1/8"
2-3/8" OR
2-3/4"
CENTER LINE
Unclip with
screwdriver
INSIDE ROSE
2
1
2
1
Remove inside rose carefully
with a at head screwdriver.
5
INSTALL INSIDE KNOB/LEVER
Keep locking bar and turn button horizontal.
Push knob/lever until catch snaps into place.
INSIDE KNOB/LEVER
2
• 50 Icon, Foothill Ranch, CA 92610-3000 USA • www.universalhardware.com • 1.877.701.7837 • 999-00404_REVB 08/17
• Backset 2-3/8" or 2-3/4"
BASE
LATCH PREPARATION
This latch comes pre-set for a 2-3/8" backset.
To change the latch for a 2-3/4" backset push the cam
1"
toward the end of the latch.
1"
2-3/8"
1/8"
2
INSTALL OUTSIDE KNOB/LEVER
SPINDLE
CAM
LOCKING BAR
KNOB/LEVER
1
INSTALL LATCH
Install as shown for appropriate latch type. Ensure bevel faces door jamb.
2-3/4"
CAM
LOCKING BAR
SPINDLE
CATCH
CAM
OUTSIDE KNOB/LEVER
6
INSTALL STRIKE
STRIKE BOX
STRIKE
OPTIONAL
3
INSTALL INSIDE ASSEMBLY
PLATE
TOWARD
DOOR EDGE
JAMB
DOOR
After the door is closed,
guardbolt should be
retracted.
CENTER LINE

Publicidad

loading

Resumen de contenidos para Hampton Universal Hardware UH40047

  • Página 1 Align cut with location tab and retracted. push rose until it snaps into place. CENTER LINE OPTIONAL ©2017 Hampton Products International Corp. • 50 Icon, Foothill Ranch, CA 92610-3000 USA • www.universalhardware.com • 1.877.701.7837 • 999-00404_REVB 08/17...
  • Página 2 Alinee el corte con la pestaña seguridad debe ser de ubicación y empuje la roseta hasta que encaje en su lugar. retraído. LÍNEA CENTRAL OPCIONAL ©2017 Hampton Products International Corp. • 50 Icon, Foothill Ranch, CA 92610-3000 EE.UU • www.universalhardware.com • 1.877.701.7837 • 999-00404_REVB 08/17...

Este manual también es adecuado para:

Universal hardware uh40048Universal hardware uh40049Universal hardware uh40050Universal hardware uh4005Universal hardware uh40052Universal hardware uh40053 ... Mostrar todo