Publicidad
Idiomas disponibles
Idiomas disponibles
To comply with FCC rules, adjustment or modification of receiver and/or
transmitter is prohibited, except for changing the code setting and
replacing the battery. THERE ARE NO OTHER USER SERVICEABLE
PARTS.
Children operating or playing with a garage door opener
can injure themselves or others. The garage door could
close and cause serious injury or death. Do not allow
ADVERTENCIA
children to operate the wall push button(s) or remote
control(s).
A moving garage door could injure or kill someone under
it. Activate the opener only when you can see the door
clearly, it is free of obstructions, and is properly adjusted.
The push buttons on the Four-Function remote controls can
activate garage door openers, entryways and/or light controls.
(Instructions for programming light products are included with
those accessories.)
In general, code switch remote controls are used when
several persons are operating the same device. Code
switches must be set to matching positions in all remote
controls used to operate the same receiver. Follow the
instructions for Figures 1 and 2. Use the "ribbed" push
button exclusively for code switch application.
Figure 1
Green
Test Light
Battery
Compartment
Cover
Push
Connector
Buttons
Battery
Access the code switches in the 84LM, four-function remote(s)
as follows:
• Remove the battery compartment cover as shown in Figure 1.
• Remove the case screw on the housing bottom.
• Hold the remote control as indicated and pull to separate the
housing. Set aside the case top (with push buttons).
Figure 2
Match Code Switches
1 2 3 4 5 6 7 8
9
+
0
Code Switches (1-9)
• Place remote circuit boards side by side. Make sure you set
code switches 1 through 9 in all remotes to matching positions
(see Figure 2). Use a pen or a screwdriver to move the
switches to (+), (-) or (0).
• Reassemble case top and bottom by snapping them together.
• Replace the case screw and battery compartment cover.
114A2025
©
WARNING
CAUTION
Ribbed
Push Button
(1-9)
1 2 3 4 5 6 7 8
+
0
Code Switches (1-9)
© 1996, Chamberlain Group, Inc.
Model 84LM Four-Function Remote Control
Program Receiver to Match Remote Control Code:
Each receiver must be programmed to accept the code of the
remote push buton that will be used to operate the device.
When several remotes will operate the same device, it is only
necessary to use the "ribbed" push button of one remote to
WARNING
program the receiver.
Select a remote control push button to operate the receiver.
• Press and HOLD the selected push button, Figure 1.
• Then press the "SMART" button on the receiver panel (see
Figure 3). The green indicator light will FLASH once. Release
the remote control push button.
Now the device will operate with the selected remote push button.
NOTE: If the remote push button is not held down until the
indicator light flashes, the receiver has not accepted the code.
WARNING
If the "SMART" button is pressed and held until the
adjacent indicator light turns off (about 6 seconds) ALL the
codes the receiver has learned will be erased.
Figure 3
Representative
Garage Door Opener
Receiver
To Attach the Remote to Your Car Visor:
• Remove the visor clip from the clip holder.
• Remove the case screw. Insert tab on clip holder through
circular label and into case, Figure 4. Slide clip holder forward.
• Replace the case screw (do not overtighten). Slide visor clip
onto clip holder.
Figure 4
Case
Screw
Bottom of
Remote
Case
The Remote Control Battery:
The green test light should glow and the device should operate
when the remote is activated.
The 9V battery should produce power for at least a year. If the
green test light is dim or does not come on, replace the battery.
To change the battery, remove the battery compartment cover,
unsnap the connector and remove the old battery (Figure 1).
9
Insert a replacement battery. Snap the connector onto the new
battery and replace compartment cover.
Replacement Parts:
9V battery ..............................10A16
Visor Clip .............................29C128
Visor Clip Holder...............31C412-1
For service, dial our toll-free number: 1-800-528-9131
All Rights Reserved
OWNER'S MANUAL
1
"Smart"
Green
Button
Indicator Light
Clip Holder
Visor Clip
Tab
Remote case only.......41A4425
(circuit board not included)
2
3
9
9
1
1
7
3
7
3
5
5
KG
KG
Case
Screw
Slide
Clip Holder
Printed in Mexico
Publicidad
