Rules For Safe Operation; General Safety Instructions - KNOVA KN RO-1200 Manual Del Usuario

SPECIFICATIONS
Motor:
120 V ~ 60 Hz 10 A
Power:
1 200 Watts (1-3/4 HP)
Speed:
11 000 – 28 000 RPM.
Collet capacity: 1/4"
Plunge stroke:
2-1/8" (54 mm)
Base dimension:
6-1/4" (158.8 mm)
Weight net/gross:
9,25/10,14 lb

RULES FOR SAFE OPERATION

KNOW YOUR TOOL
Before operating this tool, carefully read this operating manual
and all of the labels affixed to the router. Keep this manual avail-
able for future reference.
READ ALL INSTRUCTIONS THOROUGHLY

GENERAL SAFETY INSTRUCTIONS

1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres
(presence of flammable liquids, gases or dust). Power
tools create sparks that may ignite dust or fumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) ELECTRICAL SAFETY
a) A power tool plug must match its outlet. Never modify
the plug in any way. Do not use an adaptor plug on a
grounded power tool. Use the original plug in an
appropriate outlet to reduce the risk of electric shock.
b) Avoid bodily contact with such grounded surfaces as
pipes, radiators, ranges and refrigerators. The risk of
electric shock is greater if your body is grounded.
c) Do not expose power tools to rain or moisture. Leakage of
water into a power tool increases the risk of electric shock.
d) Do not mishandle the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep the cord away
from heat, oil, sharp edges and moving parts. Damaged and
tangled cords increase the risk of electric shock. Replace or repair
damaged cords. Make sure your extension cord is in good condition.
e) Use the appropriate extension cord if operating a power
tool outdoors. Use of a cord suitable for outdoor use
reduces the risk of electric shock. When using an extension
cord, be sure to use one sturdy enough for the amperage
drawn by your tool. An undersized cord will produce a drop in
line voltage, resulting in reduced power and overheating. The
IMPORTANT:
IMPORTANT: Read this operating manual carefully before using this tool. Pay close
attention to all Safety Instructions, Warnings and Cautions. Use the tool properly
and only for its intended use.
Safety symbols in this manual are used to flag possible hazards. The safety symbols
and their explanations require your full understanding. Simply reading a safety warn-
ing does not eliminate a particular hazard, nor does it substitute for proper accident
prevention procedures.
This Safety Alert Symbol indicates a caution, warning or hazard. Failure to comply
with a safety warning can result in serious injury to yourself or others. Always observe
safety precautions to reduce the risk of injury, fire or electric shock.
IMPORTANT
This tool should only be serviced by a qualified service
technician.
following table illustrates the correct cord size, depending on
cord length and the tool's ampere rating. If in doubt, use the
next heavier gauge. The lower the gauge, the heavier the cord.
Recommended sizes of extension cords
Tool's Volts
Amperage rating
0 – 6
120 V~
6 – 10
10 – 12
12 – 16
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool if tired or under the influence of drugs, alcohol or
medication. A single moment of inattention while
operating a power tool may result in serious personal injury.
b) Use safety equipment. Always wear goggles. Other safety
equipment such as a dust mask, non-skid safety shoes, a
hard hat or a hearing protection device will, when used
under the appropriate conditions, reduce personal injuries.
c) Avoid accidental start-up of the tool. Make sure the
switch is in the "Off" position before plugging it in.
Carrying a power tool with your finger on the switch
or plugging in a power tool with a switch set to "On" is a
dangerous practice.
d) Remove any adjusting key or wrench before turning on
the tool. A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
e) Do not overreach. Maintain proper footing and balance
at all times. This ensures better control over the power
tool in unexpected situations.
Total length of cord in feet
Cord size in A. W. G. (minimum)
25' 50' 100'
18 16
16
18 14
16
14
16
16
14
12 Not Recommended
150'
14
12
12