Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Quick Start Guide
INSTALL LED DOWNLIGHT INTO CEILING
OPEN WINK OR SAMSUNG SMARTTHINGS APP
ADD THE LED DOWNLIGHT TO THE HUB
CONTROL YOUR LIGHTING
• Download or update your HUB manufacturer's app.
• Turn on the LED downlight with the wall switch.
• The LED downlight will flash twice when turned
ON to indicate that the fixture is in pairing mode
• Open HUB manufacturer's app and follow pairing
instructions. See reverse side for specific Wink
and SmartThings instructions.
• After successful pairing with the HUB the LED
downlight will flash once.
• Control the LED downlight through your device
(the wall switch must remain ON).
DIMMING
The LED downlight will dim
DIMMABLE
to 5% using the HUB app.
COLOR TUNING
Use the HUB app to adjust Color
Temperature (CCT) of the RL56/ RL4
wireless LED downlight.
Connected Recessed Downlight
Works with
Works with
Amazon Echo Plus
Amazon Echo Plus
BASIC INSTRUCTIONS
NOTE: Ensure the HUB is powered on and within range of the LED downlight.
adjustable
color
CONNECT
RL56 /RL4
• The LED downlight will be ready to control
only after successful pairing to the HUB.
• The LED downlight is not designed to work with
wall dimmers or other controlled lighting systems.
• If using a dimmer with this LED downlight, set
dimmer at the highest setting for best results.
• Refer to LED downlight website for up-to-date HUB
compatibility list.
• Works with Wink and SmartThings HUBs only. Refer
to HUB manufacturing instructions or website for
scene setting, scheduling and any other app features.
ATTENTION
NOTE: For the wireless downlight to communicate
with the HUB the wall switch must remain ON.
RESET TO FACTORY SETTING
• Using the wall switch, physically switch
ON and OFF 6 times within 2 seconds.
• The LED downlight will flash twice after
a successful reset.
Photos for demonstration only.
Publicidad
Manuales relacionados para Cooper RL56
Resumen de contenidos para Cooper RL56
- Página 1 • Using the wall switch, physically switch COLOR TUNING ON and OFF 6 times within 2 seconds. Use the HUB app to adjust Color adjustable • The LED downlight will flash twice after Temperature (CCT) of the RL56/ RL4 color a successful reset. wireless LED downlight.
-
Página 2: Troubleshooting
• Relocate hub closer to fixture • Fixture is slow to respond See enclosed instruction sheet for ATTENTION HALO RL56/RL4 Wireless Series installation instructions Note: For the wireless downlight to communicate with the HUB the wall switch must remain ON. -
Página 3: Instructions De Base
Utilisez l'application du concentrateur adjustable 6 fois dans 2 secondes pour régler la température de la couleur color • Le plafonnier intensif à DEL clignotera deux fois pour indiquer (CCT) du plafonnier intensif que la réinitialisation a réussi DEL sans fil RL56/RL4. -
Página 4: Dépannage
• Relocalisez le concentrateur plus près du luminaire ATTENTION Consultez la feuille d'instructions incluse pour les instructions d'installation de la Série sans fil RL56/RL4 HALO Remarque : Pour que le plafonnier intensif sans fil communique avec le concentrateur l'interrupteur mural doit être dans la position allumée. -
Página 5: Instrucciones Básicas
Usa la aplicación HUB para ajustar la ON and OFF 6 times within 2 seconds. adjustable temperatura del color (CCT) de la luz • The LED downlight will flash twice after color empotrada de techo LED inalámbrica a successful reset. RL56 / RL4. -
Página 6: Resolución De Problems
ATENCIÓN Ver la hoja de instrucciones adjunta para las instrucciones de instalación de la Serie inalámbrica HALO RL56 / RL4 Nota: Para que la luz empotrada de techo inalámbrica se comunique con el HUB, el interruptor de pared debe permanecer encendido.