Functions; Remote Control, Front And Rear Panel Function - Sylvania 6842THG Manual Del Propietário

F
UNCTIONS

REMOTE CONTROL, FRONT AND REAR PANEL FUNCTION

SLEEP button
To turn the power off automatically at
POWER button
Channel number buttons
SETUP button
To display on-screen menu.
s / B / K / L
To move left / right / up / down through
ENTER button
To decide the command of setting when
the menu is displayed.
BACK button
To go back to the previous operation in menu.
VOL. X X / Y Y buttons
MUTE button
CH RETURN button
To return to previously viewed channel.
INPUT SELECT/ENTER
button
(p20/p13)
• To select TV or external input
mode (to access DVD, VCR,
etc.).
• To decide the command of
setting when the menu is dis-
played.
CHANNEL K K / L L buttons
To select channels and move
up/down through the menu items.
VOLUME X X / Y Y buttons
To adjust volume and move
right( X X )/left( Y Y ) through the
menu items.
NOTE:
With buttons [VOL. X/Y] or [MUTE], you can only adjust the volume of the main unit. You cannot adjust the volume of the external
devices with these buttons.
About Interference to Infrared Devices
Please note in advance that using other infrared devices
(such as infrared cordless headphones) near the plasma
display may cause infrared interference to occur.
About Pixel Defects
A plasma display is created by using a collection of miniature
pixels. It is possible to display more than 99.99% of valid pix-
els, however a small fraction of pixels over the life of the
product may not illuminate or may constantly be illuminated.
This is not to be considered a defect in the plasma panel.
6
EN
(p23)
preset time.
POWER
(p13)
To turn TV on/off.
(p18)
To select channels.
(p15)
buttons
(p13)
SETUP
the items.
(p13)
BACK
(p22)
(p18)
To adjust volume.
(p18)
To mute sound.
(p18)
(p18)
(p18)
SETUP
VOLUME
INPUT SELECT button
To select TV or external input mode (to
access DVD, VCR, etc.).
INPUT
SLEEP
SELECT
AUDIO button
• Analog mode (TV)
1 2 3
To select audio mode.
• Digital mode (DTV)
4 5 6
To select audio language.
AUDIO
7 8 9
STILL button
STILL
Pauses the image shown on the screen.
- 0
SCREEN MODE button
SCREEN
MODE
Selects aspect ratios available for the
screen.
INFO button
ENTER
• Analog mode (TV) (p22)
INFO
To display channel No., signal type
and TV setting.
CH RETURN
• Digital mode (DTV) (p22)
To display channel information, signal
VOL. CH
MUTE
type and TV setting.
• External mode (p20)
To display external mode, signal type
and TV setting.
CH K K / L L buttons
To select channels and external input
mode.
INPUT SELECT /
SETUP VOLUME CHANNEL ENTER STANDBY ON POWER
INPUT SELECT /
POWER
STANDBY ON
CHANNEL ENTER
Preventing Image Burn on the plasma display
Fixed images displayed on the plasma display for an
extended period of several hours may cause uneven pixel
aging causing damage to the plasma display. You should
try to avoid displaying fixed images for extended periods
on the plasma display.
Images of high luminance displayed on the plasma display
for more than 60 seconds may cause lingering images to
remain on the screen. These images will automatically disap-
pear, but may take time depending on the luminance of the
images and how long they were displayed on the screen.
(p20)
(p19)
(p19)
(p21)
(p18/p20)
Infrared Sensor Window
To receive the infrared rays
transmitted from the remote
control.
STANDBY indicator
Lights up when the power is in
the standby mode. Disappears
when the power is ON.
ON indicator
Lights up when the power is ON.
POWER button
To turn TV on/off.
SETUP button
(p15)
To display on-screen menu.