Technical Specifications - Master RIO Manual De Uso Y Mantenimento

USER MANUAL
motor with mechanical limit switch for venetian blinds
Dear customer, thank you for purchasing a MASTER product. This manual describe the operations for a correct installation of the product. This device is not
design for a continuative use. Use of the product other than that provided for in this manual is improper and prohibited and will void the warranty and any
manufacturer's liability. The installation of the product must be done by a qualified technician. At the end of the installation, all manuals must be given to the end
user. Keep this manual for future reference!
To facilitate, improve and speed up any request to the assistance service it is necessary to provide the product name to the operator.
Before installing the motor, it is recommended to copy the technical data (including the extended product name) and store them in a safe place

01. TECHNICAL SPECIFICATIONS

Power supply
Rated speed
Rated torque
02. WARNINGS
02.1 Warnings for safety
Incorrect installation can cause serious injuries
programming and maintenance operations must be carried out only by a qualified and skilled technician, who must comply with laws, provisions, local regulations and the instructions
●
given in this manual The wiring must comply with current IEC standards. The final electrical system must be created only by the electrician
operation and can exclude the use of radio controls or require particular safety devices
shutter/awning regularly
02.2 Warnings for installation
Check that the package is intact and has not been damaged in transit A heavy knock and the use of unsuitable tools can cause the damage of the external or internal parts of the motor
●
Do not pierce or tamper with the motor in any way. Do not modify or replace parts without the manufacturer's permission
The product may not be used if the power cable is damaged. Do not try to replace the power cable Any screws needed to complete the installation must not come into contact with the
●
motor The power of the motor must be sufficient for the applied load (check the rated data shown on the motor)
from another support surface, the moving parts must be protected with a cover to prevent accidental access. In any case, ensure access for maintenance work The power cable must
be positioned in such a way that it does not come into contact with moving parts
sight of the roller shutter/awning but a long way from its moving parts. Position the buttons more than 1.5 m from the floor
continuous operating time is 4 minutes
if it overheats. The motor returns to normal operation when its temperature drops below the safety limit (normally after 8 to 12 minutes)
come into contact with liquids and in any case in a position protected from atmospheric agents
is powered
02.3 Warnings for use
The product is not intended to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are
supervised or given instructions about the product way of use by a person responsible for their safety
●
until the movement ends Do not allow children to play with the appliance or with the fixed control devices
out (e.g. window cleaning, etc.). If the control device is automatic, disconnect the motor from the power line
The limit switch adjustment buttons are covered by rubber caps. They are used to guarantee the indicated IP protection
degree: once the limit switches have been adjusted, replace the caps in their seats.
Caps to remove
to reach the buttons for
adjustment of limit switch
R
Information for any assistance requests
: 230 V~ 50 Hz Rated power
-1
: 26 min
: 2x4,5 Nm Rated current
: 2x9,5 Nm
●
Keep these instructions for future maintenance work and disposal of the product
●
●
During operation, the motor body becomes very hot, so be careful The motor contains a self-resetting thermal cut-out, which stops the motor
RIO
: 152 W (2x4,5)
: 260 W (2x9,5)
: 0,7 A (2x4,5)
: 1,25 A (2x9,5)
●
To prevent potentially dangerous situations, check the operating condition of the roller
●
●
If the product is installed at a height of less than 2.5 m from the floor or
●
If installed outside, it is a good work place the cable in a protective tube
●
●
For your safety, do not work near the winding roller while the motor
●
Check the automation during the movement and keep people at a safe distance,
●
Do not operate the blind when maintanance operations are being carried
IMPORTANT:
STOP button
(if mounted)
WHITE button:
adjustment of
LOW limit switch
01
Continuos operating time
IP insulation
Insulation class
Max n° of turns
●
All the product installation, connection,
●
Some applications require hold-to-run
●
Do not carry the motor by the power cable.
●
Position the buttons within
●
The motors are designed for residential use; the maximum
●
The motor must be installed so that it cannot
rev00 24.09.2020
: 4 minutes
: IP54
: H
: 100
●
GREEN button:
adjustment of
UP limit switch