JUNO 6RLC Retrofit Trim Serie Instrucciones De Instalación

IMPORTANT: For your safety, read and understand instructions completely before starting installation. Before wiring to power supply, turn off electricity at the
fuse or circuit breaker box.
NOTE: Juno recessed products are designed to meet the latest NEC requirements and are classified in compliance with the applicable UL standards.
Before attempting installation of any recessed lighting product, check your local electrical building code. This code sets the wiring standards and installation
requirements for your locality and should be understood before starting work.
SAVE THESE INSTRUCTIONS
Product Information
Suitable for damp locations. Also suitable for wet locations indoor covered
ceiling only.
This product is intended for use as a retrofit trim installed into a 6"
open frame rough-in section only.
The product consists of the following: Retrofit trim with pre-wired flexible
conduit whip assembly (conduit fitting included), Universal Mounting Bracket
and installation instructions. Check for all contents prior to installation.
Do not make or alter any open holes in an enclosure of wiring
or electrical components during kit installation.
THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE
WHERE THE SUITABILITY OF THE COMBINATION SHALL BE
DETERMINED BY CSA OR AUTHORITIES HAVING JURISDICTION.
WARNING - Risk of fire or electric shock.
• Installation of this retrofit assembly requires a person familiar with the
construction and operation of the luminaire's electrical system and the
hazard involved. If not qualified, do not attempt installation.
Contact qualified electrician.
• Install this kit only in luminaires that have the construction features and
dimensions described in these instructions, and where the input
rating of the retrofit kit does not exceed the input rating of the luminaire.
WARNING - To prevent wiring damage or abrasion, do not expose wiring to
edges of sheet metal or other sharp objects.
IMPORTANT: Trims must be grounded as outlined below. Failure to do so can
result in electric shock or undesired operation.
The trim assembly must be electrically grounded either through the conduit
whip/junction box connection or through the universal mounting bracket
contact with rough-in section. This requires that the junction box be electrically
grounded and/or the universal mounting bracket be electrically grounded.
Refer to Figure 1 to identify the subject components.
To use this product in an ungrounded rough-in section, consult factory for
additional instructions.
IMPORTANT: Power to the luminaire must be turned off prior to installing
these LED retrofit trims. Failure to do so can cause electric shock, which can
result in injury or death.
Dimming
Juno retrofit LED trims require 120VAC input and are dimmable with most
incandescent, magnetic or electronic low voltage wall box dimmers*.
Contact Juno Lighting Group Product Services or visit
www.junolightinggroup.com for a current list of compatible dimmers.
Trim assembly has integral LED electronics. Replace entire trim
assembly in the event of failure.
* Electronic low voltage dimmers require a neutral wire connection in the wall box.
WARRANTY
Juno Lighting Group provides five year limited warranty on LED components from date of purchase. Juno Lighting Group's obligation is expressly limited
to repair or replacement, without charge, at Juno Lighting Group's factory after prior written return authorization has been granted. This warranty shall not
apply to products which have been altered or repaired outside of Juno Lighting Group's factory. This warranty is in lieu of all other warranties, expressed
or implied, and without limiting the generality of the foregoing phrase, excludes any implied warranty of merchantability. Also, there are no warranties which
extend beyond the description of the product on the company's literature setting forth terms of sale.
Product Services Phone (888) 387-2212
1300 South Wolf Road • Des Plaines, IL 60018 • Phone 800-323-5068 • Visit us at www.junolightinggroup.com
Detail A
Rough-In Section Ring
Torsion Spring Receiver Clip
(Clamps to Ceiling and or Rough-In Section Ring)
INSTALLATION INSTRUCTIONS
Juno Retrofit LED Trim Compatibility
This Juno Retrofit LED trim is designed to work with most standard UL listed
commercial recessed open frame rough-in sections with a ceiling thickness
ranging from 1/2" - 1-1/4". Rough-in section compatibility can be determined
by measuring the recessed open frame rough-in section ring inside diameter
(Refer to Detail A). Open frame rough-in section inside diameter compatibility
range is from 5-13/16" - 7-1/8". Ceiling thicknesses and rough-in section
construction features vary and these ranges should be used as a guideline.
Installation
If the rough-in section has been modified, the loose warning label with this
retrofit kit must be affixed to the luminaire in a location visible after installation.
Step 1. Install the enclosed trim assembly.
Turn off electricity at the fuse or circuit breaker box. Remove existing trim
section and housing (if applicable) to gain access to the rough-in section
junction box. Remove junction box access cover to gain access to the wiring.
Disconnect all primary input wires leading from 120V input supply to the
ballast or socket. Install the supplied trim conduit whip into the junction box via
knockout using supplied 1/2" trade size fitting. Connect 120V supply wires to
retrofit trim wires (black trim wire to positive, white trim wire to neutral). Make
certain junction box or universal mounting bracket is grounded (See Step 2).
Reinstall junction box cover (See Step 2).
Step 2. Install Universal Mounting Bracket assembly.
Collapse the Universal Mounting Bracket to fit into the open frame rough-in
section. Expand the brackets legs until they fit the open frame and sit flat on
top of the rough-in section as illustrated in Figure 1. Secure the horizontal
adjustment by tightening the horizontal locking screw. Secure the Universal
Mounting Bracket by turning the vertical clamping screw clockwise until the
clip located at the end of the torsion spring receiver clamps to either the
ceiling and/or rough-in section ring depending on rough-in section or ceiling
style. (Refer to Detail A) Secure both sides of the bracket. When clamping is
completed confirm the Universal Mounting Bracket is secure before installing
the retrofit trim.
Insert trim torsion springs into corresponding torsion spring retaining brackets
located on the Universal Mounting Bracket. Carefully push trim towards ceiling
until the springs pull the trim flush to the ceiling.
Make certain wires are not pinched or damaged during installation.
* In some instances the Retrofit Trim may utilize existing torsion spring
brackets and the Universal Mounting Bracket may not be necessary.
Step 3.Turn power on to fixture.
Conduit Fitting
(1/2" Trade-Size)
Universal
Mounting Bracket
Feet (4X)
© 2015 Juno Lighting, LLC.
For 6RLC Retrofit Trim Series
Conduit Whip with Integral Fitting
for Junction Box Connection
Junction Box Access Cover
Horizontal Locking Screw
Vertical Clamp Screw (2X)
Torsion Spring Receiver (2X)
See Detail A
Open Frame Rough-In Section
Torsion Springs (2X)
Juno LED Retrofit Trim Assembly
Figure 1
Printed in U.S.A. Rev 4/15 P3782 pg 1 of 1