Remote Control - Rewell Revellutions ROAD RIDER 42 Manual Del Usuario

1 vehICle
1A Tyres with 1C Gear shifting
quick-change 1D ON/OFF switch
system
1E LiPo battery
1B Interchangeable
1F Lock
springs

2 reMoTe ConTrol

2A Power LED Switching on:
2B ON/OFF switch Briefly press the
power button;
2C Steering
the power LED
2D Speed controller
illuminates
2E Battery compartment
Switching off:
Press and hold
the power but-
ton, the power
LED goes out
3 aCCessorIes
3A Charging unit
3B LiPo battery
3C Key for battery lock
3D Mains adapter for charger
5 ChargIng The vehICle baTTery
Attention: Before charging and after each use, the battery and the motor must cool down
for 10 to 15 minutes. Otherwise, the battery or motor can be damaged. Do not leave the
charging process unsupervised.
5A Switch off the remote control and vehicle!
5B Open the battery lock with the key.
5C Remove the battery from the vehicle.
5D Plug in the charging unit; the green LED lights up. Insert the battery; the red LED
lights up. When the red LED on the charging unit has turned off the charging process
is complete. Unplug the charging unit and remove the battery.
5E Re-insert the battery in the vehicle and lock it in place again with the key.
When charged for about 60 minutes, the vehicle can drive for about 30 minutes,
depending on driving style and gear. if the battery is empty, the car stops in order
to prevent a harmful total discharge of the battery.
14
Required batteries for the vehicle:
Power supply:
Rated output:
DC 3,7 V / 1000 mAh / 3,7 Wh
Batteries: 1 x 3,7 V rechargeable
LiPo battery (included)
Capacity: 1000 mAh
Battery requirements
for the controller:
Power supply:
Rated output: DC 6 V
Batteries: 4 x 1,5 V „AA" (not included)
Charging unit technical data:
Suitable for LiPo batteries 7.4 V / 2S /
750–2000 mAh in the Revell hard case
4 InserTIng baTTerIes
4A Unscrew the cover.
4B Insert 4 x 1.5 V AA batteries and
pay attention to the polarity speci-
fication, as shown in the battery
compartment.
4C Close the battery compartment
cover and tighten the screw.
6 sTarT preparaTIon
First, briefly press the ON/OFF button on
the remote control; the power LED
illuminates (6A). Then switch the ON/OFF
on the vehicle to the "ON" position (6B).
When switching off, always switch off the
vehicle first (cf. 6B), then the remote
control (cf. 6A)! Otherwise, a drive
command can accidentally be triggered,
causing the vehicle to drive away on its
own, which can lead to considerable
damage.
Battery saver function: After 5 min.
without actuation, the remote control
makes a peep tone and the Power LED
blinks. After an additional 5 min. it
switches off entirely. The vehicle also
switches off approx. 3 min. after the
remote control switches off.
To resume driving, switch the remote
control on again and switch the vehicle
off and on again with the ON/OFF switch.
8 vehICle ConTrol
8A Driving forward: 8B Braking and
driving in reverse
To start and drive
forward, carefully pull To brake, carefully push the
back on the speed speed controller forward
controller. To drive until the vehicle comes to a
faster, carefully pull stop or slows down. To drive
the speed controller in reverse, push the speed
further back. controller forward again.
9 ConneCTIng The vehICle To The reMoTe ConTrol
The connection of your vehicle to your remote control is already established at the
factory. Should it become necessary to re-establish connection, proceed as follows:
• Switch off the remote control and car.
• Squeeze the speed controller until it is completely in and hold it there.
Turn and hold the steering wheel all the way to the right. Turn on the remote control
now and the LED will blink.
• Place the remote control directly next to the vehicle and switch it on.
• As soon as the power LED on the remote control illuminates continuously, the
connection has been established and you can drive.
7 sTeerIng TrIM adjusTMenT
The correct trim is a basic requirement
for fault-free driving behaviour from the
vehicle. Adjusting the trim is easy, but it
requires a little patience and a feel for it.
Please follow the following
instructions precisely:
if the vehicle pulls to the left or the
right without being steered...
use the trim lever to correct the wheel
alignment by turning it in the opposite
direction. The wheel alignment can be
found on the bottom of the vehicle (cf. 7).
8C To drive along a left-
handed curve, turn the
control to the left as long as
the rear end faces the driver.
8D To drive along a right-
handed curve, turn the
control to the right as long as
the rear end faces the driver.
15