Pelican 9470 Manual De Usuario

CATALOG No. 9470
Pelican™ 9470 User Manual
Pelican™ 9470
The Pelican™ 9470 Remote Area Lighting System (RALS)
contains four LED light heads, four masts, two 12V sealed
lead acid batteries and a power supply all contained within
a Pelican™ protector case. The masts will extend to a height
of nearly 7 feet and the light heads can articulate in multiple
directions.
Mast Operation
1. Open case, remove lamp heads & masts then stand case
upright.
2. Screw lamp heads onto masts then insert masts into mast
holders (see image A).
3. Connect lamp head plugs into the corresponding sockets
located on the top of the case (see image B).
4. To extend the mast, release the clamp on each section
and raise. Lock each clamp when you have reached your
chosen height.
5. To collapse the masts, reverse the procedure.
Image A Image B
Light Operation
1. Press power button on keypad once to switch on. The default setting is the preset
high mode (as indicated by the three 'sun' symbols at the top of the screen). Your
remaining run time is displayed in the center of the screen and your battery level
at the bottom of the screen (see image C).
2. Press the bottom left button on the keypad to change between high, medium
and low power. You will notice that your remaining run time alters between these
settings.
3. Press the up or down buttons on the keypad at any time to enter the Intelligent
Control "IC" mode (see image D). The IC mode allows you to select any run time
up to 24hrs. In this mode, your power level is displayed at the top of the screen
instead of the preset 'sun' symbols. You can go back to the preset mode at any
time by pressing the bottom left button on the keypad.
4. Press the power button on the keypad to switch off.
Image D
The 9470 RALS features the ability to run directly from the power supply without
discharging the battery; when the power supply is connected to mains AC power the
9470 will automatically select a light level to allow continuous operation - automatic
mode. (In this automatic mode, the battery level will remain constant). The light level
will be approximately at 50% of maximum capacity. The display on the keypad will
adopt the IC mode, showing the battery level and power level, but the timer display
will be replaced by "--:--" and the hourglass icon will disappear. Manual adjustment
of the brightness will still be possible, however if the brightness is increased, then
automatic mode will be exited, a new runtime will be computed based upon the
new operating conditions. The battery level and the display will revert to the
normal IC mode, (or preset mode if the bottom left button has been used). If the
brightness is decreased, the unit will remain in continuous mode (and the battery
will charge up slowly).
If the power supply is removed, the unit will return to normal operation and
the run-time display will show the remaining time for the particular setting prior to
removal of the power supply.
Bluetooth Operation
The 9470 RALS is equipped with Bluetooth capability which allows you to operate it
via the Pelican™ RALS app.
1.800.544.2843
Image C
Image E
www.calcert.com
15
10 20
5 25
0 30
To download the RALS app, visit the app store and search for 'Pelican™ RALS'. Once installed the
app icon should appear on your screen. The app supports both iOS and Android devices.
The Bluetooth is active by default so once you open the app your 9470 RALS should appear under
the 'Found' heading (see image E) as per the following example: 9460C/9470C_00000X (the last
six digits are your unique serial number). By clicking on this serial number the app should connect
to your 9470 RALS and the serial number should now appear under the 'Connected' heading in the
app screen. The Bluetooth logo on the 9470 screen should turn from white to blue. You can connect
to multiple RALS but only operate one at a time.
Once connected, the default setting is always off. To switch on you can either press the 'on/off'
toggle on the app screen or slide the intensity slider until you reach your desired light intensity. The
app works in conjunction with the keypad screen on your 9470 RALS; as you adjust the slider on
the app screen, the remaining run time adjusts accordingly.
The app will remain connected until you either close the app or go out of range*, at which point the
Bluetooth logo on the 9470 keypad screen will turn from blue to white. You can override the app
control by operating the 9470 RALS keypad if desired.
The Bluetooth can be manually deactivated on the 9470 if required. To deactivate it, switch the
RALS on then press and hold the bottom left button on the keypad until the Bluetooth logo in the
bottom left of the screen disappears. It can be reactivated again by pressing and holding the same
button again until the logo reappears.
*Range varies depending upon the environment in which the RALS is being used.
Flash Mode
1 Press and hold the power button for 5 seconds until flashing begins, then select the required
power level.
2. To switch flashing mode off, press the power button again.
Battery Level
The battery level is indicated at the bottom of the screen. When the unit is turned off, the battery
level is displayed in a dimmed mode once every 5 seconds.
Battery Charging
1. Remove the dust cap from the charging socket and plug in the mating plug from the power
supply (see image F).
2. Connect the power supply to the mains AC power supply.
3. The charge level will be indicated in the bottom of the screen display. Once a complete charge
level is reached, the display will revert to a dim display.
12v Power Supply Port
The 12v power supply port is located on the top of the case (see image G).
Remove the dust cap to expose the power socket. This can be used to provide power for
compatible devices.
Image F
Image G
USB Dual Power Adapter
The 9470 RALS includes a dual USB power adapter that can be plugged into the 12v power supply
port to power/charge other USB compatible devices (see image H).
WARNING:
ALWAYS CHARGE THE PRODUCT WITH THE CASE LID FULLY OPEN.
ONLY USE APPROVED POWER SUPPLY & ENSURE CHARGING IS CARRIED OUT IN A
WELL VENTILATED ROOM.
DO NOT STORE THE PRODUCT IN A DISCHARGED STATE.
WHEN NOT IN USE, RECHARGE THE PRODUCT AT LEAST ONCE EVERY 3 MONTHS.
Battery Replacement
Contact your dealer for a replacement battery.
Battery Safety Information
WARNING: HANDLE AND STORE BATTERIES PROPERLY TO AVOID INJURY OR DAMAGE
BATTERIES CAN BE DANGEROUS!
Most battery issues arise from improper handling of batteries, and particularly from the use of dam-
aged or counterfeit batteries. Please review the information below to avoid serious injury and/or
damage to your property.
Rechargeable Batteries
1. Hazardous location safety approvals for explosive environments are only valid for the Pelican
battery pack that is supplied with the light.
2. For replacement battery packs only use the approved Pelican battery pack for the model of the
light that you are using. The use of other battery packs will invalidate the safety approval.
3. Lights should only be charged in a non-hazardous location.
4. Lights should only be charged using the Pelican charger base that is supplied with the light.
5. Lights should be charged and operated between the temperatures shown: Charge Tempera-
ture: -20°C to 50°C (-4°F to 122°F) Operating Temperature: -20°C to 50°C (-4°F to 122°F).
6. Do not charge with alkaline batteries installed in the light. Attempting this can cause internal gas
or heat generation resulting in venting, explosion or possibly fire.
7. Deep discharge of the rechargeable battery may cause batteries to vent potentially dangerous
gasses and electrolytes.
Always dispose of all batteries properly at an approved battery recycling center.
Image H
sales@calcert.com