Publicidad
Idiomas disponibles
Idiomas disponibles
•
Before taking into operation, every stand has to be checked upon possible damages. If one part of a stand is defective, the stand must not
be taken into operation.
Before lifting or lowering the telescopic tubes, you must always block a safety area around the stand. This safety area must have a
•
diameter of 1.5 times the maximum height.
•
Stands with their loads have to be secured against unintended movements, also in case of fire.
•
Depending upon the individual installation spot, all necessary measures against movement and for securing the standing safety have to
be created.
When people are located below the load, all necessary safety measures have to be taken in order to avoid injury. The personnel has to be
•
instructed on the content of the user manual and on the dangers related with operating stands.
•
Operate the stand only after having become familiar with its functions. Do not permit operation by persons not qualified for operating the
device. Most damages are the result of unprofessional operation!
•
Lifted telescopic tubes always have to be secured with a secondary securing!
•
All fixtures and T-bar attached on a stand must be secured with a secondary attachment!
•
When choosing the installation-spot, please make sure that the stand has to be installed in a way that no person can enter the area below
the stand or its load!
•
This stand must only be installed at a solid, plane, anti-slip, vibration-free and fire-resistant location.
•
Never install any objects offering a large surface for winds (e.g. banners, signs, etc.).
•
The loads have to be installed in a balanced way.
•
Always fix the fixtures with an appropriate safety-rope.
•
The stand must never be moved before having lowered all telescopic tubes!
Never dismount the winch handle or any element of the winch under any circumstances.
•
Please consider that unauthorized modifications on the stand are forbidden due to safety reasons!
•
•
Dry the product after use in damp conditions to avoid triggering corrosion especially when using it near marine environments.
•
The product is not designed to be used immersed in liquids.
•
Never remove the serial code and production date from the stand as this would make the guarantee void.
•
If this stand will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee
becomes void. Furthermore, any other operation may lead to dangers like crash.
Before installing the stand, make sure that the installation area can hold a minimum point load of 5 times the system's load (e.g. weight
•
20 kg - point load 100 kg).
•
The installer is responsible for adhering to the carrying capacity given by the manufacturer, the safety requirements and the qualification
of possible co-workers.
•
The stand must not be left unattended or accessible to unauthorized persons. Keep away children!
•
Stand may not exceed the maximum load of 40kg.
•
The stand should only be set up on a horizontal level surface.
•
The stand must be set up on firm ground capable of taking both the weight of the stand and its load without sinking in.
•
Carefully check that there are no electrical cables or live parts located in the area occupied by the stand and its load.
All loads should be balanced especially when using T-Bar.
•
Unlock lever screw "A", press tripod base "B" down and spread the legs "C" outwards. To obtain
maximum stability, position the leg brace "D" parallel to the ground. Lock the legs and tripod base
by tightening the lever screw.
lower lever screw "E". The centre column must never touch the ground as this adversely effects
the stability of the stand.
For use in the open secure the stand with safety cables (not delivered). In windy conditions, avoid to load large reflectors.
The stands have telescopic centre column height adjustment. Locking lever screw are used to secure the columns in place.
Check the column (s) is locked tight by applying pressure down before loading the stand. This should be checked regularly! When
lowering each telescopic column, firmly support the load and column by clamping the relevant column with one hand whilst
unlocking lever screw.
Telescopic section may not reach maximum height. As soon as "STOP" or "MAX" label is visible on the telescopic tube,
lower the telescopic part immediately.
It's also possible to lower the centre column by undoing the
Publicidad
