User Interface - LiftMaster Star1000EV Manual Del Usuario

APPLICATION
The STAR1000EV is a high capacity single channel access control receiver for door
operators, and dry contact triggered devices. The STAR1000EV is compatible with EVO
Code (Security+ 2.0 ) remote controls. The receiver capacity is 1,000 devices and can be
™
any combination of remote controls and wireless keyless entries. The receiver is watertight
according to IP44 specification. This receiver is compatible with HomeLink
INSTALLATION
1. Select a convenient location near the operator to be controlled by the receiver within "line
of sight" of the intended transmitting location.
NOTE: Do not mount LCD screen in direct sunlight. Avoid mounting the receiver in a metal
enclosure or near other wireless receiving or transmitting devices.
2. Mount the bracket to the desired surface with appropriate hardware (not provided) (Fig. 1).
3. Remove the 4 screws on the back of the receiver and remove the faceplate. Unplug the
keypad connector from the control board.
NOTE: Be careful not to damage the keypad cable while removing the faceplate.
4. Make wiring connections (Figure 2). Refer to your gate or commercial door operator
owner's manual for more specific information.
5. Reconnect the keypad connector to the board (labeled J9).
6. Secure the faceplate with the 4 screws previously removed.
7. Install the antenna provided.
NOTE: Use an antenna extension kit to mount the remote antenna as high and far from
metallic objects as possible for the best radio range.
8. Snap the receiver onto the mounting bracket and secure with the screws provided.
9. Tighten the watertight connector to secure and seal the wiring.
Figure 1
Antenna Connector
Backup Memory
Module
Keypad Connector

USER INTERFACE

The STAR1000EV user interface consists of a 22 character by 5 line
LCD display, 3 "soft keys", Down/Up arrows and a numeric keypad.
Scroll Indicator
If more than 3 options exist, a scroll
indicator appears on the left margin of
lines 2, 3, and 4. The scroll indicator
shows the relative position within
the list.
Line 1:
Menu and function mode.
Lines 2, 3 and 4:
Menu selections and data.
Line 5:
Soft key function modes.
.
®
Mounting Bracket
Waterlight Connector
Antenna Connection
For the direct antenna or
the antenna extension kit.
Menu/Data selection
shown in inverse font.
To prevent possible SERIOUS INJURY or DEATH from electrocution:
• The installer (specialist) must carefully read and understand these instructions before
starting any work.
• Be sure power is NOT connected BEFORE installing the receiver.
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER permit children to
operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and
there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
• The STAR1000EV must be installed at a height below 2 m.
• All-pole mains switch is required to be incorporated in the electrical installation of the
building.
To prevent possible SERIOUS INJURY or DEATH, the use of CONSTANT OPERATION
on residential openers is PROHIBITED. The receiver can be installed on door operators
which comply with the essential standards EN12453, EN 60335-2-92 and E60335-2-103.
Figure 2
9 - 30 Volts AC/DC
250 mA max
Power Supply**
PROGRAMMING
The receiver has the ability to learn a combination of remote control
transmitters and keyless entries up to 1,000 devices. Audible and
visual warnings occur when the receiver capacity is exceeded. After 30
LCD Screen
seconds of inactivity, the receiver times out and the LiftMaster
System
displayed. Select "UNLOCK" and enter the PIN to continue.
programming and
status display.
Initial PIN set up:
"SOFT" Keys The PIN restricts access to authorized administrators only. If you omit
Soft key functions this step, anyone will be able to program the receiver. Upon initial
are defined by the power up, the system firmware revision is displayed for 5 seconds
label on line 5 of the followed by the LiftMaster® logo. When a key is pressed, "CREATE
display. The functions
PIN?" is displayed.
change according to
1. Press "YES" to create PIN. If the PIN is lost you may request a
the menu selection.
Down/Up Keys
2. Enter a 6-digit PIN, and press "YES"; enter the 6-digit PIN a second
For navigation in
the menus.
Numeric Keypad
3. When your 6-digit PIN is programmed correctly, the LCD display
Numeric data is
entered through the
numeric keypad.
Insert wiring
ACCESS CONTROL RECEIVER
MODEL STAR1000EV
WARNING
WARNING
Relay
Connection
Power
Connection
Single Operator
reset code by pressing "RESET".
time and press "YES" to program the PIN. If you make a mistake,
press "CLEAR" to change your entry. To exit the enter PIN screen,
select "BACK".
reads "KEYPAD UNLOCKED". Select "OK" to continue to the Main
Menu. After 30 seconds of inactivity, the receiver times out and the
LiftMaster logo is displayed. Select "UNLOCK" and enter PIN to
®
continue.
en
Receiver Without
Faceplate
Control
Station
logo is
®