LiftMaster Star1000EV Manual Del Usuario página 3

Receptor de control de acceso
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

PROGRAMMING COMMANDS*
The table below describes the commands used to program the receiver.
MAIN MENU
COMMAND
LEARN MENU
LEARN DEVICE
LEARN TO LOC #
DELETE MENU
DELETE DEVICE
DELETE ALL DEVICES
SUSPEND MENU
SUSPEND DEVICE
SUSPEND ALL DEVICES
UNSUSPEND DEVICE
UNSUSPEND ALL DEVICES
QUERY MENU
LOC # USED
LOC # AVAILABLE
LOC # SUSPENDED
CHANGE PIN
SETTINGS
DEALER INFO
FIRMWARE VERSION
BEEP
MEMORY
RELAY
CONTRAST
LANGUAGE
FACTORY DEFAULT
*Further information: liftmaster.eu
System Capacity..........................................................................
Supply Voltage............................................................................
Operating Current........................................................................
Stand By Current.........................................................................
Surge Suppression......................................................................
Operating Temp Range...............................................................
Storage and Shipping Temp Range.............................................
Frequency....................................................................................
Relay Contact Rating...................................................................
Remote Controls..........................................................................
Keypads.......................................................................................
12 V DC Transformer
(optional, indoor use only) ..................
**
* Compatible list: liftmaster.eu
** Power supply must be used according IEC62368-1 Type PS2.
(Optional - 12 V DC Transformer Model TDX-1200500 indoor use only (SKU: UPS-TDX)
The packaging must be disposed of in the local recyclable containers. According to the European Directive 2002/96/EC on waste electrical equipment, this device must be properly dis-
posed of, after usage in order to ensure a recycling of the materials used. Old accumulators and batteries may not be disposed of in the household waste, since they contain pollutants
and must be properly disposed of in municipal collection points or in the containers of the dealer provided. Country-specific regulations must be observed.
Hereby, Chamberlain GmbH declares that the access control receiver type Star1000EV is in compliance with Directive 2014/53/EU.
DUPLICATE MEMORY
RESTORE MEMORY
SPECIFICATIONS
1000 devices
9 - 30 Volts AC, 9 - 42 Volts DC
50 mA Maximum
30 mA Maximum
6.0 kV Min
-40°C to +65°C @ 50% Rh
-40°C to +85°C @ 50% Rh
EVO Code, Security+ 2.0™ (433, 868 MHz)
1 amp @ 24V AC/DC
COMPATIBLE ACCESSORIES*
TX2EV/S, TX4EV/S/F, TX4UNI/S/F
747EV
UPS-TDX
The full text of the EU declaration of conformity is available at the following internet address:
https://chamberlain.de/Chamberlain/media/Chamberlain/CE/DoC_Star1000EV.pdf
DESCRIPTION
Program a device to the receiver.
Program a device to a 4-digit number location.
Delete a specified device that has been programmed to the receiver.
Delete all programmed devices.
Temporarily disables the function of a specified device that has been programmed to the receiver.
Temporarily disables the function of ALL devices programmed to the receiver.
Re-enable the function of a suspended device.
Re-enable the function of ALL suspended devices.
Displays a range of used locations starting from a specified location.
Displays a range of empty locations starting from a specified location.
Displays a range of suspended locations starting from a specified location..
Change the 6-digit PIN number for the receiver.
Display and edit the dealer contact phone number.
Displays the current firmware version.
Turn the audible feedback on or off.
Creates a memory backup. A backup memory module must be installed.
Restores a memory backup from a memory module.
NOTE: Content of memory backup module will over-write any
information already stored in the receiver memory.
Sets the relay activation time from .25 to 1 second.
Press Down or Up arrows to adjust LCD contrast.
Sets menu language: English (Default), Spanish, and French.
Reset receiver to factory default settings.
EVENT
Key press
Successful Add
Successful Delete
Successful Suspend
Successful Unsuspend
Master PIN entry error
Programming error
Location out of range
Generic Success
Generic Error
Received unknown Tx
Received known Tx
Received known suspended Tx
DIAGNOSTICS
The receiver emits a series of audible beeps to signal programming and error
events. The table at right lists all of the events and their audible notifications.
The On/Off column indicates that the audible notification for the event may be
disabled in the BEEP SETTINGS menu.
AUDIBLE
ON/OFF
NOTIFICATIONS
Single
YES
Double
Triple
Double
Double
Long
Long
Long
Double
Long
Slow
YES
Double
YES
Long
YES

Publicidad

Tabla de contenido
loading

Tabla de contenido