Orbis MODUL LOG Manual Del Usuario página 3

MODUL LOG/MINI LOG/MINI T LOG
Day of the week/Date
(dd-mm-yy)
C1 circuit state
ON - ON
OFF - OFF
- Permanent
- Override
- Pulse
- Cycle
1 2 3 4 5 6 7 AMPM
Current time
Day of the week
(1= Monday..)
Time scale
0 3 6 9 12 15 18 21 24
ON
OFF
Move up in menu
C1: ON OFF
1 2 3 4 5 6 7
AM PM
C Ok
MENU
Cancel the selection
Move back in menu
DESCRIPTION
MODUL LOG / MINI LOG / MINI T LOG are digital time
switches with 1 changeover switch and potential free
designed for the control of any electrical installation. Its
possibilities include short-duration (1-59 seconds) switching,
repeating cycles, random programming, automatic summer-
winter time change and a time counter.
Its menus can be displayed in 5 languages and it displays a
chronogram of that day's programming. This divided into 48
section, each section representing 30 minutes. The section
corresponding to the current time flashes.
INSTALLATION
ATTENTION: Electrical devices must be installed and assembled
by authorized installer.
VERY IMPORTANT: The switch is protected internally against
interference by a safety device. However, particularly strong
electromagnetic fields may alter
interference can be avoided by adhering to the following
recommendations during installation:
- The device should not be installed near inductive loads
(motors, transformers, contactors, etc..)
- A separate power line is recommended ( equipped with a
network filter if necessary).
- Inductive loads should be equipped with interference
suppressors (varistor, RC filter).
If the timer switch is to be used in combination with other
devices in an installation, it is necessary to verify that no
parasitic disturbances will be caused by the group
ASSEMBLY: In panel (MODUL LOG), DIN rail or surface
mounting (MINI LOG) and flush mounting (MINI T LOG).
CONNECTION: Connection scheme
5 4 3 2 1
L N
STARTING UP
Factory settings for MODUL LOG / MINI LOG / MINI T LOG
includes the current date and time and the following
configuration:
Time: Central European time (E.U.)
Clock: 24 h mode
Winter-summer time change Automatic (last
Sunday in March)
Summer-winter time change Automatic (last
Sunday in October)
Holidays: NO (off)
Random mode: NO (off)
C1 counter: Zeroed (0000 hours)
Programs: None (memory empty)
PROGRAMMING
Programming is menu-based (text messages).
If operations are programmed for the same time, remember
that some have priority over others
The order of priority is as follows:
PERMANENT MODE →HOLIDAY PROGRAM →
RANDOM PROGRAM → PULSE ON →
PULSE OFF→PROGRAMMING OFF→
PROGRAMMING ON→CYCLE PROGRAMMING
The information being programmed always flashes on display.
Pressing the "OK " key brings up the PROGRAM MENU.
If the language used is not right, reset the timer.
RESET
When all four keys are held down for more than 3 seconds, all
existing programming is deleted and the LANGUAGE menu
appears.
LANGUAGE SELECTION
Use the UP ∆ and DOWN ∇ keys to choose a language and
confirm pressing "OK ." The DATE YEAR menu then appears
TIME SWITCH
automatically.
CLOCK SETTING
Press "OK" to go into the PROGRAM menu and use the ∆
and ∇ keys to select the DATE menu. Confirm with "OK" to go
Chronogram
Currentime into DATE YEAR. The numbers for the year flash on display
(flashing)
and are changed with the ∆ and ∇ keys. Confirm with the
"OK" key. The figures for MONTH and DATE are entered in
the same way. Press "OK" to save the date (dd, mm, yy), the
day of the week will be set automatically and the display will
Random
change automatically to TIME programming. Use the ∆ and ∇
Holidays
keys to change, first, the hours, confirm with "OK", then
Summer time
repeat for the minutes. Press "OK and the PROGRAM menu
Winter time
will appear.
AM/PM mode If you first wish to check the information entered, press the
"C" key and the timer goes back into normal mode
Display
BASIC PROGRAMMING
PROGRAM MENU
In normal mode, press the "OK" key to bring up the
PROGRAM menu. Press "OK" again and the display will show
Move down in menu
PROGRAM PROG 01.
Circuit C1 override
ON-OFF PROGRAMMING
Press the "OK" key again and you will see on display PROG
01: PROGRAM. Confirm pressing "OK" and the display will
show PROG 01:
switch type ON-OFF, PULSE or CYCLE. Confirm the choice
Confirms the selection
with the "OK" key. The display automatically shows MON :
Starts menu
YES. If you want the switch to be carried out on Monday,
press "OK," otherwise, press either of the ∆ and ∇ keys and
the display will show MON : NO. Press "OK" and carry out the
same process for the other days of the week, one after the
other, confirming them in the same way.
When you have selected the days, you then need to set the
time at which the switch will take place. Use the ∆ and ∇ keys
to set the hours and confirm with "OK, " then do the same for
the minutes. When you confirm the time pressing "OK," the
display will show PROG 02: PROGRAM. Press "OK" again
and the display will show PROG 02 C1 : ON. Follow the
same steps as for Program 01. There are 50 memory spaces
(PROG 01 to PROG 50).
When you have finished programming, press the "C"
repeatedly until the normal display appears.
VIEWING PROGRAMMED SWITCHES
Press "OK" to go into the PROGRAM menu, then "OK" again
to bring up PROGRAM PROG 01 on display. Press the ∆ and
is operation. Such
∇ keys to see all the programs (1 to 50).
CHANGING OR DELETING SWITCHES
Press "OK" to go into the PROGRAM menu, then "OK" again
to bring up PROGRAM PROG 01 on display. Use the ∆ and ∇
keys to select the program you wish to change (1 to 50 ) and
when you have it, press "OK" and the program will be shown
on display with the word MODIFY. The ∆ and ∇ keys change
between CLEAR and MODIFY, Choose your option and press
the "OK" key.
If you chose CLEAR, the program will be eliminated and the
display will show PROGRAM and the program deleted
(PROG XX).
If you have chosen MODIFY, pressing "OK" brings up the
type of switch selected (ON-OFF / PULSE / CYCLE) and you
should carry
PROGRAMMING. To return to normal operation, press the
"C" key repeatedly until the normal operating display is
shown.
MANUAL ACTIVATION
The C1 circuit can be temporarily activated or deactivated by
pressing the ∇ key. A
until a programmed switch takes place.
It is also possible to activate or deactivate ( any programed
maneouvre is made ) the circuit permanently by following
these steps:
Press the "OK" key to go into the PROGRAM menu and use
the ∆ and ∇ keys to change the 2nd line on the display until
you see MANUAL. Confirm by pressing "OK" and the display
will show MANUAL C1: ON. Use the ∆ and ∇ keys to choose
between ON – OFF – ON
(Permanent). Confirm by pressing "OK" and go back to
normal mode by pressing the "C" key repeatedly. To change
out of permanent mode, repeat this operation and select ON
or OFF.
In the ON
state of the circuit by pressing the ∇ key, in normal mode.
The symbols for activated options are shown on display.
ADVANCE
(EXTRAS)
PULSE PROGRAMMING
With pulse programming, switches from 1 to 59 seconds can
be carried out, with both ON and OFF pulses.
In normal mode, press the "OK" key to go into the MENU
PROGRAM. Press "OK" and the display will show:
PROGRAM PROG 01 .
Press the "OK" key again and the display will show PROG 01:
PROGRAM. Press "OK" again and PROG 01:
appears. Use the ∆ and ∇ keys to select PULSE, press "OK"
to confirm and the display will show MO : YES. If you want the
switch to be carried out on Monday, press "OK," otherwise,
press either of the ∆ and ∇ keys and the display will show
MO : NO. Press "OK" and carry out the same process for the
other days of the week, one after the other, confirming them
in the same way.
(See exemple )
C1: ON. Use the ∆ and ∇ keys to choose
on as described in the section
symbol will be shown on display
(Permanent) – OFF
and OFF positions, you can also change the
PROGRAMMING. SPECIAL FUNCTIONS
When you have selected the days, you then need to set the
time at which the switch will take place. Use the ∆ and ∇ keys
to set the hours and confirm with "OK. " Now do the same for
the minutes and when you confirm by pressing "OK," the
display will show PULSE ON : choose the second when the
circuit is to be connected using ∆ and ∇ and confirm with
"OK". The display will show PULSE OFF. Use ∆ and ∇ to
select the second at which the circuit is to be switched off and
press "OK" again to confirm.
If you want an "on" pulse, take care to set PULSE ON before
PULSE OFF and the other way round for an "off" pulse
Pulse ON
(start second)
i.e.- 12:04:05
WINTER / SUMMER TIME CHANGE
To go into the menu MENU, press the "OK" key and use the ∆
and ∇ keys to find the EXTRAS option. Confirm with "OK" and
you will see EXTRAS SEASON on display, press "OK" again
and 3 options are displayed: AUTO, MANUAL and DO NOT
USE. Move between them with the ∆ and ∇ keys and confirm
by pressing "OK."
AUTO (the clock is automatically changed on the last Sunday
in March and the last Sunday in October).
No changes are possible with this option. When you select it,
the display shows SEA AUTO W
change from winter to summer time (last Sunday in March).
When "OK" is pressed, SEA AU
and when the ∆ or ∇ key is pressed, the time of the change
(02:00:00) is shown. When you press "OK" again, you will see
SEA AUTO S W and the date of the summer-to-winter
time change (last Sunday in October). Pressing "OK" shows
the date again and the ∆ or ∇ key lets you see the time when
the change will happen (03:00:00). Press "C" or "OK" to go
back to the EXTRAS HOLIDAYS menu.
MANUAL (Allows you to choose the date and time for the
time change).
When you select this option, the display shows SEA MANUAL
W S and the date of the winter-to-summer time change.
Press "OK" and you can change the month with the ∆ and ∇
keys. When you confirm this (OK), you see LS (for "Last
Sunday"): YES. If you want to set the last Sunday of the
chosen month for the change, press "OK," otherwise change
to LS: NO using the ∆ and ∇ keys and confirm with "OK."
If you accept LS: NO, the next display allows you to choose
the day of the month when the change will take place,
followed by the hours and minutes. When you confirm with
"OK," the summer-to-winter time change (S
program in the same way. "OK" takes you back to the
EXTRAS HOLIDAYS menu.
DO NOT USE (no time change will be made)
If you select this option and confirm (OK), no time change will
be made and you will be taken back to the EXTRAS
HOLIDAYS menu.
If there are any switches programmed during the period of the
time change, they will be duplicated or not carried out,
depending on the time change in question.
HOLIDAY PROGRAM
This allows you to cancel programs and switch the circuit OFF
on
for a set period of time. When this time has passed,
programming is re-established.
Press "OK " to go into the MENU PROGRAM, use the ∆ and
∇ keys to find EXTRAS, press "OK" and use the ∆ and ∇ keys
again to find HOLIDAYS. Accept ¨" OK " and the display will
show HOLIDAYS BEGIN and press OK again to see BEGIN
HOUR. Use ∆ and ∇ to enter the hour at which the holiday
period is to begin, press "OK" and then enter MINUTE,
MONTH and DAY in the same way. Confirm the setting with
"OK" and the display will show HOLIDAYS END. Program this
in the same way as for HOLIDAYS BEGIN, entering your
chosen HOUR, MINUTES, MONTH and DAY for the holiday
period to end. When you press "OK" to confirm the last of
these, you will see EXTRAS RANDOM on display – press the
"C" key repeatedly to go back to normal working.
During the holiday period, the symbol
display.
DEACTIVATING THE HOLIDAY PROGRAM
To deactivate the holiday program, go into EXTRAS
HOLIDAYS and with HOLIDAYS BEGIN on the display, use
the ∆ and ∇ keys to select CLEAR, then press "OK" and the
program will be erased. Press "C" repeatedly to go back to
normal operation.
RANDOM PROGRAMS
The MODUL LOG / MINI LOG / MINI T LOG can carry out
random "on" and "off" switches. Random programs work
between 07:00 and 24:00.
The program RANDOM
variable duration, between 10 minutes and 1 hour.
The program RANDOM
variable duration, between 2 and 4 hours.
From the normal operating display, press "OK" and use ∆ and
C1: ON
∇ to find EXTRAS RANDOM. Press "OK" again and you will
see RANDOM 1. Use ∆ and ∇ to choose between the
options 1, 2 or STOP, which deactivates the random
program. Press "OK" to confirm and press the "C" key
repeatedly to go back to normal operating mode. If one of the
random programs has been selected, the symbol
displayed on display.
In random mode, programmed switches are not carried out.
Pulse OFF
(finish second)
i.e.- 12:04:32
S and the date la of the
W S DATE appears
W) is shown -
is displayed on
1 carries out random switches of
1 carries out random switches of
will be