Battery Precautions - HoMedics HSD-100 Manual De Instrucciones E Información De Garantía

How to use the CLEAN Function: If you wish to change the type of liquid in Hand Sanitizer, you may
use the CLEAN function to empty and clean the unit. Press the [CLEAN] button and the unit will enter
the auto cleaning mode: 1.) first the Red LED will illuminate for 12 seconds to allow you to replace the
battery door and position the unit for cleaning, 2.) then the motor will turn on and pump for 30 seconds.
During this period, you can press the [CLEAN] button again to abort the cleaning function (motor will
turn off). The CLEAN function will work with the Dispenser Control Switch set to [1], [2] or [3]; it will not
work with the Dispenser Switch in the OFF position. Repeat until there is no more liquid in the reservoir.
To thoroughly flush out the unit, you should add water to the reservoir and repeat the cleaning process.
IMPORTANT:
1. The Motion Detector that activates dispensing uses a sensitive infrared sensor. To avoid accidental
dispensing of liquid/saop, please do not place Hand Sanitizer Dispenser in direct sunlight.
2. After a period of inactivity, the lotion inside Hand Sanitizer Dispenser may become dry and clog the
Hand Sanitizer. Should this occur, simply use a toothpick or water to remove
the obstruction.
3. The only part of the Hand Sanitizer designed to be wet is the liquid reservoir and spout. Do not
immerse the Hand Sanitizer in water as the product will be damaged.
4. Remove batteries from the battery compartment and run the CLEAN Function to flush the liquid/soap
reservoir with water whenever the Hand Sanitizer is to be left unused for a
long period of time.
5. To clean the unit, use a soft damp cloth. Do not clean with a abrasive materials or corrosive
substances.
Trouble Shooting:
No Soap/sanitizer Dispensed; Motor Does Not Run
1. Ensure that Dispensing Control Switch is turned ON in the 1 = LOW; 2 = MEDIUM or
3 = HI position; not OFF.
2. Hands are placed directly between the Motion Sensor and Spout.
3. Unit is not placed in bright sunlight which will interfere with Motion Sensor operation.
4. Batteries are installed with correct polarity (+/ -) and not dead.
No Soap/Sanitizer Dispensed; Motor Runs
4
1. During start-up you may need to activate the Motion Sensor several times to "prime" the pump to
begin dispensing soap/sanitizer.
2. The soap/sanitizer reservoir should be at least ¼ FULL.
3. Make sure that no dried soap/sanitizer is clogging the spout or pump tubing. Use a toothpick to
clean the spout. If necessary, empty the soap/sanitizer tank, fill with water and run the CLEAN
Function.

Battery Precautions:

1. Use AA alkaline batteries only. Do not use rechargeable batteries.
2. Replace all batteries at the same time.
3. Clean the battery contacts and the contacts of the device prior to battery installation with a dry cloth.
4. Ensure the batteries are installed correctly with regard to polarity (+ / -).
5. Remove batteries from the unit when it is not to be used for an extended period of time.
6. Remove depleted batteries from the unit promptly. Dispose of used batteries safely. Keep all
batteries away from children. Batteries are small objects and could be ingested. If swallowed,
contact a physician at once. Do not open batteries or dispose of in fire. Do not mix the new and
used batteries.
Note: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
5