Safety Regulations - EINHELL DLST 9m+1m Manual De Instrucciones Original

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.

1. Safety regulations

Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
1. Workplace safety
a) Keep your work area clean and well illu-
minated. Untidy or unlit work areas can result
in accidents.
b) Do not operate the electric tool in an en-
vironment where there is a risk of explo-
sions and where there are infl ammable
liquids, gases or dust.
c) Keep the tool out of the reach of children
and other persons. If there is a distraction,
you may lose control of the appliance.
2. Safety of persons
a) Be careful, watch what you are doing and
use the tool sensibly. Do not use the tool
if you are tired or under the infl uence of
drugs, alcohol or medication. A moment of
distraction when using the tool can result in
serious injuries.
b) Wear personal protection equipment
and always wear safety goggles. Wearing
personal protection (such as dust masks,
non-slip safety shoes, safety helmet or ear
protection, depending upon the type and use
of the tool) reduces the risk of injury.
c) Make sure that the appliance cannot start
up accidentally. Ensure that the tool is
switched off before you connect it to the
supply, or pick up or carry the tool.
Anl_SA_DLST_9m+1m_SPK8.indb 10 Anl_SA_DLST_9m+1m_SPK8.indb 10
GB
d) Avoid abnormal working postures. Make
sure you stand squarely and keep your
balance at all times. In this way, you can
control the tool better in unexpected circum-
stances.
e) Wear suitable work clothes. Do not wear
loose clothing or jewellery. Keep hair, clo-
thes and gloves away from moving parts.
Loose clothing, jewellery or long hair can get
trapped in moving parts.
f) If vacuuming devices and draining de-
vices can be fi tted, make sure that these
are correctly attached and correctly used.
The use of a dust extraction system can redu-
ce the danger posed by dust.
3. Usage and treatment of the electric tool
a) Do not overload the appliance. Use the
correct tool for your work. You will be able
to work better and more safely within the gi-
ven performance boundaries.
b) Keep unused electric tools out of the
reach of children. Do not allow people
who are not familiar with the appliance or
who have not read these instructions to
use the appliance. Electric tools are dange-
rous if they are used by inexperienced people.
c) Clean your electric tool carefully. Check
whether moving parts are functioning
properly and not jamming, whether parts
are broken or damaged enough that the
functioning of this tool is aff ected. Dama-
ged parts must be repaired before using
the appliance. Many accidents are caused
by badly maintained tools.
d) Make sure to use tools, accessories,
spare parts, etc. in accordance with these
instructions. Take the conditions in your
work area and the job to perform into ac-
count. Using tools for any purpose other than
the one for which they are intended can lead
to dangerous situations.
4. Service
a) Have your tool repaired only by trained
personnel and/or the authorized service
agent, using only genuine spare parts.
This will ensure that your tool remains safe to
use.
Special safety information
•
After use, switch off the compressed air and
empty the hose, making it easier to roll the
hose up.
•
The equipment must only be operated in an
- 10 -
19.10.2016 10:46:15 19.10.2016 10:46:15