Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Center hitch on flat
Surface of crossmember
Hitch Shown In Proper Position
Equipment Required: Pullwire (Provided)
Fastener Kit: K24681
Wrenches: 11/16, 7/8
Drill Bits: ½"
Existing outboard
Hole driver side
j
Qty. (2)
Carriage Bolt ½-13 x 1-3/4 GR5
k
Qty. (2)
Spacer ¼ x 2 x 2
l
Conical Toothed Washer ½"
Qty. (2)
m
Qty. (2)
Hex Nut ½-13
1.
Raise hitch into position centered on vehicle.
2.
With hitch in position, identify location of existing holes on vehicle bumper and crossmember.
3.
Enlarge holes in vehicle bumper at locations identified in Step 2.
Using access slot, individually fishwire block and 7/16" Carriage Bolt into the existing holes in crossmember.
4.
5.
Install fasteners as shown above.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z1999, 2000, 2001, 2006, 2009, 2015 Cequent Performance Products – Printed in México
Installation Instructions
Chevrolet Impala
Fascia
Drawbar Kit:
3595
(Sold separately)
Drawbar must be used in the
RISE position only.
Crossmember
nopq
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg.) Max Gross Trailer Weight
200 LB (90.8 Kg.) Max Tongue Weight
Wiring Access Location: PC3, PC4
jklm
n
Qty. (2)
Carriage Bolt 7/16-14 x 1-1/4 GR5
o
Qty. (2)
Spacer
p
Conical Toothed Washer 7/16"
Qty. (2)
q
Qty. (2)
Hex Nut 7/16-14
Sheet 1 of 3
Part Numbers:
24681
77082
Existing holes
ENLARGE THESE HOLES.
Bumper
Existing outboard slot
Passenger side
N24681
10-20-15
Rev. D
Form F206 Rev A 5605
Publicidad
Manuales relacionados para Cequent Performance Products 24681
Resumen de contenidos para Cequent Performance Products 24681
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. z1999, 2000, 2001, 2006, 2009, 2015 Cequent Performance Products – Printed in México Sheet 1 of 3...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spé cifications en matiè re de sécurité des systèmes d’attelage. z1999, 2000, 2001, 2006, 2009, 2015 Cequent Performance Products – Imprimé au Mexique Feuille 2 de 3...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulació n V-5 y SAE J684. z1999, 2000, 2001, 2006, 2009, 2015 Cequent Performance Products – Impreso en México Hoja 3 de 3...