Cequent Performance Products 24850 Instrucciones De Instalación

Body
Bumper
Panel
Fascia
Muffler
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24850F
Wrenches: 13mm, 9/16"
Drill Bits: None
Other items: Round file as
needed.
7
1
See Steps 4 & 5
below and Figure 2
next page for
installation Notes.
1 Qty. (3) 8mm -1.25 CL10 Flanged Locknut, (1 extra)
2
Qty. (3) 7/16" Flat Washer (15/16" outside diameter ,1 extra)
3
Qty. (1) 3/8"-16 x 1-1/2" Gr.5 Hex head Bolt (as needed)
4 Qty. (1) 3/8"-16 x 1-3/4" Gr.5 Hex head Bolt (as needed)
1. Raise hitch into place by turning hitch sideways under vehicle , then carefully raising one end between back of muffler and plastic bumper
fascia. Then raise other end into place. If vehicle is not raised on hoist or ramps be careful not to scratch plastic bumper fascia.
2. Hang hitch bracket clearance holes over existing 8mm stud/weldnuts located just rear of mufflers on both sides of vehicle. See Figure 1
next page. Make sure that 3/4" diameter clearance holes in hitch brackets sit flat against vehicle sheet metal and do not rest against vehicle
weldnuts.
3. Install one 7/16" flat washer, (smaller diameter washer), over one of the existing 8mm studs in vehicle and against hitch bracket just hung in
Step 2 above. Then start 8mm flanged locknut on stud and tighten with wrench just enough to keep hitch bracket against vehicle sheet metal.
Note! hitch brackets cannot rest on top of weldnuts on
Install flat washer and locknut on other side of vehicle the same way making sure that hitch brackets are against vehicle sheet metal and not
against weldnuts. As previous tighten locknut just enough to keep hitch in place so that it doesn't fall against weldnuts.
4. Raise forward hitch attachment aligning with existing slot in bracket hanging down off bottom of independent suspension crossbeam. It may
be necessary to remove (2) exhaust rubber isolators from hangers to access attachment.
5. Using heavy flat washers, (larger diameter washers), stack together to make up gap between hitch bracket and vehicle bracket.
Caution! make sure that 3/8" bolt is just long enough to go through flanged locknut and doesn't bottom out against aluminum
transaxle. See Figure 2 next
different length 3/8" bolts. Use the one that works best for your particular vehicle so that bolt does not bottom out against aluminum
transaxle but still extends through locknut.
6. Torque 8mm nuts installed in Step 3 to torque shown below for 8mm locknuts. Torque 3/8" bolt installed in Step 5 to torque shown below
for 3/8" bolt. Reinstall rubber isolators on exhaust if removed.
Tighten 3/8"-16 Gr.5 bolt with torque wrench to 30 Lb.-Ft. (41 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2009, 2011, 2012, 2015 Cequent Performance Products, Inc – Printed in Mexico
Installation Instructions
Chevrolet Camaro
All Models, Excluding convertible
(will not fit vehicles with optional dealer
installed ground effects package)
(Sold separately)
Drawbar Kit:
3594
Drawbar must be used in
the RISE position only.
Exhaust
hanger
2
page. You may have to put flat washers under head of bolt to keep bolt from bottoming out. Supplied are (3)
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Hitch type
Weight Carrying
Ball Mount
Wiring Access Location: PC1 , PC2
8
6
Use the
8
3
one
length
4
bolt that
works
5
best.
5
Qty. (1) 3/8"-16 x 2" Gr.5 Hex head Bolt (as needed)
6
Qty. (1) 3/8" Conical Toothed Washer
7
Qty. (1) 3/8" -16 Flanged Locknut
7/16" Heavy Flat Washer (1-1/4" outside diameter).
8
Qty. (10)
Use as needed, you may not need all of them.
vehicle. Existing weldnuts must show through hitch bracket clearance holes.
Tighten 8mm locknuts with torque wrench to 27Lb.-Ft. (37 N*M).
Sheet 1 of 6
Part Numbers:
24850, 60266,
77223, 24893
U-Haul
Max Gross Max Tongue
Trailer WT (LB) WT (LB)
2000 (908 Kg) 200 (91 Kg)
1
2
See Steps 2 & 3
below and Figure 1
next page for
installation Notes.
24850N 10-8-15
Form: F205 Rev A 5-6-05
Rev. D