Publicidad
EN
IMPORTANT
Please read these instructions carefully before you start to assemble this greenhouse.
Keep these instructions in a safe place for future reference.
» Customer Service
For assistance with assembly or for replacement parts – please log onto our website
or call our service line (number is on the title page).
Additional information can be found at our website: www.palramapplications.com
» Safety Advice
•
It is of utmost importance to assemble all of the parts according to the directions.
Do not skip any step.
•
We strongly recommend using work gloves during assembly.
•
Always wear shoes and safety goggles when working with extruded aluminium.
•
If using a step ladder or power tools ensure that you follow the manufacturer's
safety advice.
•
Do not touch overhead power cables with the aluminium profiles.
•
Do not attempt to assemble the greenhouse in windy or wet conditions.
•
Dispose of all plastic bags safely keep them out of reach of small children.
•
Keep children away from the assembly area.
•
Do not lean against or push the greenhouse during construction.
•
Do not position your greenhouse in an area exposed to excessive wind.
•
Do not attempt to assemble this greenhouse if you are tired, have taken drugs or
alcohol or if you are prone to dizzy spell.
•
Hot items such as recently used grills, blowtorches etc. must not be stored in the
greenhouse. Ensure there are no hidden pipes or cables in the ground before
inserting the pegs.
•
This product is designed to use as greenhouse only.
» Care & Maintenance
When your greenhouse needs to be cleaned, use a mild detergent solution and
rinse with cold clean water. DO NOT use acetone, abrasive cleaners or other special
detergents to clean the clear panels. It is recommended to check periodically that
roof panels caps (plastic part 329 & profile 981) are set in place.
» Tools & Equipment
•
Tape measure
•
Work gloves
•
Lubricant
•
Phillips head screwdriver
•
Step ladder
•
Drill bit
•
Large hammer
•
Spanner
•
T001 - Special tool for Screws 411 and nuts 412
» Before Assembly
This is a multi-part assembly best
achieved by two people. Allow at least
half a day for assembly process.
Selecting a site - the greenhouse must
be , positioned and fixed on a flat level
surface.
Choose a sunny position away from
overhanging trees.
We are strongly recomend to fix your
greenhouse directly to a solid concrete
foundation. When doing that use the
pre drilled holes in the metal base
supplied.
Take out all components parts of the
packages. Sort the parts and check
against the contents parts list.
During assembly parts should be laid
out close at hand. Keep all small parts
(screws etc.) in a bowl so they do not
get lost.
In purpose to facilitate parts'
identification and assembly process,
all-positioned profiles are used in this
greenhouse. As a result some
apertures in the profiles
are not used during
assembly.
• Screws 411 and nuts 412 are used throughout the assembly process.
• Screws 411 are to be assembled from the outside and nuts 412 from the inside of the
greenhouse.
• If not specified otherwise, do not fasten screws and nuts (411 & 412) more than 2-3
turns only. Do not tighten them until completion of the panels' assembly. These 2
icons indicate if screws' tightening is required or not.
• However, in some steps, temporary tightening of a few screws may be needed to
prevent a profile from falling till it will be fully connected in the next steps.
» During Assembly
During assembly you will encounter the
information icon, please refer to the relevant
assembly step for additional comments and assistance.
Carry out the assembly steps in the order set out in the
instructions.
Step 6: Make sure the base is square by measuring the
diagonals and level by using a spirit level.
Determines the front side of the greenhouse.
Step 11: You may use silicon lubricant spray in
order to help you slide the panels into the profiles.
Do not spray the Polycarbonate panels. Use the
rubber mallet if necessary.
Door assembly
Steps 88-96: Door assembly should be done
according to these steps.
Window assembly (Steps 50-52, 74-76, 81-84)
Step 51: Decide on the window's location before
assembly. Window can be installed in one of the
indicated options.
Step 84: In case the window is not closed properly,
please release the screws step 76a+b, adjust the profile
and tighten the screw.
Firmly connect the greenhouse to a level final position
immediately after completion of the assembly.
Tighten all screws when completing assembly.
Step 97: Make sure the cable is threaded in the hole
(#7329) and does not interfere with the opening the
window.
Step 98: Anchor the greenhouse to the ground by using
part #7331 for hard surface or part #7336 for soft surface.
Step 100: Stretch the cable by using part #7332
Publicidad
