Audio And Power Connections; Connecting To Audio Sources; Audio Outputs; Connecting To Power - AKG Acoustics HEARO 999 AUDIOSPHERE II Modo De Empleo

3 Audio and Power Connections

Note:
3.1 Connecting to
Audio Sources
Refer to connecting dia-
gram (fig. 1) and Table 1.
Table 1: Audio connec-
tions vs. required cables.
Note:
Note:

3.2 Audio Outputs

3.2.1 Connecting to a
Stereo Amplifier
3.2.2 Connecting
Stereo Headphones
3.3 Connecting to
Power
Refer to fig. 2.

4 Operating Notes

4.1 Important Notes

18
You may use the transmitter either free-standing or install it in a 19" rack using the optional
RMU 60 rack mount kit. (If you install the transmitter in a 19" rack, do not make your audio
and power connections before installing the transmitter.)
1. Before connecting the HEARO 999 AUDIOSPHERE II to your audio source, switch power
to your audio source OFF.
2. Make the desired audio connections.
You can connect the HEARO 999 AUDIOSPHERE II to any analog headphones output
(mini jack or 1/4" jack), to the LINE or REC output of your amplifier, or to an optical or
coaxial digital output. To connect the transmitter to a coaxial output, use a commercial
connecting cable with an RCA connector at each end (not supplied with the transmitter).
Analog audio source
Headphone output
Mini jack
1/4" jack
LINE OUT/REC OUT
2 x RCA jacks
Digital audio source
Optical output
Coaxial output
When using an analog audio source, check that the DIGITAL switch (2) is OUT. When using
a digital audio source, check that the DIGITAL switch (2) is IN.
You can connect each digital input to a digital audio source and use the DIGITAL IN
switch (17) to toggle between the two audio sources.
1. Switch power to your audio source OFF.
2. Use the supplied AK 1 RCA cables to connect the "TAPE IN", "AUX IN", or
"PLAYBACK IN" jacks on the amplifier to the LINE OUT jacks (15) on the HEARO rear
panel.
3. Refer to the operating manual of your amplifier for instructions on how to listen to and
mute the signal at the TAPE", "AUX", or "PLAYBACK" input. On most amplifiers, you can
push the "TAPE MONITOR" switch IN to listen to the processed signal and OUT to cut
the processed signal.
1. Connect the stereo jack plug on your hardwire stereo headphones to the PHONES
jack (5). You can use the VOLUME control (6) to set the volume of the headphones.
1. Connect the DC cable on the supplied AC adapter to the POWER jack (13) on the HEARO
rear panel.
2. Check that the AC voltage stated on the AC adapter is the same as that avail-
able in your country. If it is, connect the AC adapter to a convenient AC outlet.
Before setting up your system, please remember the following points:
1. Operating switches on or connecting the HEARO 999 AUDIOSPHERE II to your audio
source may cause clicks which at high volume settings may affect your hearing.
Therefore, be sure to set the VOLUME control on the wireless headphones or the
VOLUME control (6) on he HEARO to minimum before switching between different
sources (tuner, turntable, CD player, etc.) or connecting the HEARO.
2. Listening over headphones at high volume levels, particularly over extended periods of
time, may damage your hearing.
3. The transmitter incorporated in your HEARO 999 AUDIOSPHERE II is a radio frequency
device that conforms to the strict European and FCC standards. For physical reasons
that are not related to the quality of the product, extremely strong interference sources
may affect reception. In order to maintain interference-free listening pleasure, do not
operate your HEARO 999 AUDIOSPHERE II in the close vicinity of radio equipment, cel-
HEARO 999 AUDIOSPHERE II
LINE IN
L/R (2 x RCA jacks)
L/R (2 x RCA jacks)
LINE IN
L/R (2 x RCA jacks)
DIGITAL IN
OPTICAL
COAXIAL
Connecting cable
AK 2
AK 2 + stereo adapter
Connecting cable
AK 1
Connecting cable
DK 1
Coaxial cable