Cequent Performance Products 24909 Instrucciones De Instalación

Frame rail
Rearward
Fascia
Hitch Shown In Proper Position
Equipment Required: Galvanic
isolators (provided), lubricant
or soapy water, tin snips,
Fastener Kit: 24909F
Wrenches: M10, 11/16, & 3/4
Drill Bits: 1" hole saw
Muffler
Tail pipe
1 1 1 1
Qty. (1) Carriage bolt ½-13 X 2.00 GR5
2 2 2 2
Qty. (1) Spacer ¼" x 1.50 x 3.00
3 3 3 3 Qty. (3) Conical washer ½"
4 4 4 4 Qty. (1) Hex nut ½-13
1. Lower exhaust at the rubber isolator. Spraying a lubricant or soapy water on the metal hanger rod and the rubber isolator helps removal.
2. Remove rearward m6 bolt holding heat shield in place. Return to owner. Trim heat shield for access to hole on passenger frame rail. Fig 3
3. Remove the black box (charcoal canister ) from frame by removing M8 bolt and sliding the box forward.
4. Using 1" hole saw, drill a access hole into side of driver and passenger side frame rail inline with the existing hole to insert handle nut. Fig 2
5. Install ½" handle nuts into frame thru drilled holes.
6. Install the ½ carriage bolt and spacer as shown in Fig 1., to the tie down hook.
7. Apply the clear galvanic isolators to the passenger side bracket as shown. Fig 1
8. Raise the hitch into position and install conical washer and nut to tie down attachment, do not tighten down at this point. Fig 1.
9. Feed the 1/2 fasteners through slots on both sides and install fasteners as shown Fig 1. Note: on passenger side sandwich the heat shield between the frame
rail and the hitch.
10. Center the hitch on the vehicle.
11. Torque all fasteners to specifications shown below.
12. Reinstall black box (charcoal canister) removed in step 3.
13. Reinstall exhaust.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and
exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut
access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©
2013, 2015 Cequent Performance Products, Inc
Made in Mexico
Installation Instructions
NISSAN VERSA NOTE
Drawbar must be used in the
RISE position only.
Trim heat shield as shown.
Access hole under heat
shield passenger side only
Frame
rail
6
Rubber
isolator
Figure 3
Trim heat shield as
shown.
*Drivers side only
Tighten all ½-13 GR5 fasteners that use a handle nut with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
(Sold separately)
Drawbar Kit:
3592
Wiring Access Location: PC3, 4
Drill access hole for
handle nut.
5
3
1
2
3
4
Figure 1
5 5 5 5
Qty. (2) HANDLE NUT ½ -13
6 6 6 6
Qty. (2) BOLT ½ -13
7 7 7 7 Qty. (2) GALVANIC ISOLATOR
Sheet 1 of 3
Part Numbers:
29175 UH
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Figure 2
5
Tie down hook
6
24909N 10-6-15
Form: F205 Rev A 5-6-05
24909
60340
77296
Galvanic
isolators
between
heat shield
and hitch
bracket
7
3
Exhaust & heat
shield not shown
Rev. E