Cequent Performance Products 24902 Instrucciones De Instalación

Frame rail
Hitch Shown In Proper Position
Equipment Required: Pullwires (provided), Lubricant or
Soapy water, Philips screwdriver, Utility Knife, Tape Measure &
Marking Pencil.
Fastener Kit: 24902F
Wrenches: M10, 11/16" & 3/4"
Drill Bits: ½"
A. Insert bolt and
Block into frame B. Align block on
access hole
Figure 4
Reverse pullwire procedure
Tie down hook
spacer orientation
Figure 2
Access hole
Figure 5
1 1 1 1
Qty. (1) Carriage bolt ½-13 X 1.75 Gr. 5
2 2 2 2
Qty. (1) Spacer .25 X 1.50 X 3.0
3 3 3 3
Qty. (1) Conical washer ½"
4 4 4 4
Qty. (1) Hex nut ½-13
Caution: due to different manufacturing plants the holes in the frame will vary in position. Drilling may be required
1. Lower exhaust by removing both rubber isolators from muffler hangers. Spraying a lubricant or soapy water on the metal hanger rod and the rubber isolator
helps removal
2. Remove the appearance panel on driver's side if present. Obtain owners permission to trim or return to owner. See Figure 3
3. Remove rubber plug in frame rails, loosen the heat shield if needed.
4. On North American built vehicles install 7/16 carriage bolt and spacer using reverse pull wire procedure leaving pull wire attached. See Figure 4 Identify if
drilling is required - Asia built sedans enlarge holes in frame rail. Install 7/16 carriage bolt and spacer through access holes, leave pull wire attached. On the
Coupe enlarge holes in frame rail. Install 7/16 carriage bolt and spacer through access holes, leave pull wire attached. See Figure 5
5. Place 1/2" carriage bolt and spacer on tie down hook orientation as shown. See Figure 2
6. Raise passenger side of hitch over exhaust, and loosely install center attachment, feed pull wires through rearward slot on sedan and forward slot on coupes.
Install remaining fasteners as shown. See Figure 1
7. Tighten all fasteners to the required torque specification.
8. Reinstall the vehicle exhaust. Re-install appearance panel if removed and trimmed.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z 2012, 2015 Cequent Performance Products, Inc. – Printed in Mexico
Installation Instructions
Fascia
Hyundai Elantra Sedan
Hyundai Elantra Coupe
Drawbar must be used in the
RISE position only.
C. Pull bolt thru
block
8-1/8"
1"
1-3/4"
Area to trim on
appearance panel
Bumper
Figure 3
Kink pull wire to keep block
independent of bolt
Tighten all 7/16" Gr5 fasteners with torque wrench to50 Lb.-Ft. (68 N*M)
Tighten all 1/2 Gr5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Sold separately
Drawbar Kit:
3594
Example of
North American
made frame rail
Clearance
hole for
stud
Coupe –
Sedan -
mounting holes
mounting
holes
2 2 2 2
3 3 3 3
Figure 1
Note: Fasteners typical
both sides
5 5 5 5
Qty. (2) Carriage bolt 7/16-14 X 1.50 Gr5
6 6 6 6
Qty. (2) Spacer .25 X .88 X 3.00
7 7 7 7
Qty. (2) Conical washer 7/16"
8 8 8 8
Qty. (2) Hex nut 7/16-14
Sheet 1 of 3 24902N
Part Numbers:
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, 4
Enlarge hole with ½"
drill as required
Tie
5 5 5 5
down
6 6 6 6
hook
1 1 1 1
4 4 4 4
7 7 7 7
8 8 8 8
10-6-15
Form F206 Rev B 9-17-2012
24902
60329
77289
Example of
Asia made
frame rail
Access
hole
Coupe – enlarge
hole with ½" drill
Forward
Rev. B