Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Fish wire (provided)
Fastener Kit: 24908F
Wrenches: 3/4"
FRAME
ACCESS HOLE
IN BOTTOM OF FRAME
KINK FISHWIRE
TO KEEP BLOCK
INDEPENDENT OF BOLT
EXAMPLE OF FISHWIRE PROCEDURE
1 1 1 1
Qty. (4)
Carriage bolt –1/2-13X1.75 GR5
2 2 2 2
Qty. (4)
BLOCK .250 x 1.00 x 3.00
1.
Raise car on ramps or hoist.
2.
Fish wire the frame rail fasteners into place through the access hole shown above. Leave the fish wires attached.
3.
Raising hitch into position, routing fish wires thru hitch holes, being careful not to push fasteners back into the frame.
4.
Remove the fish wires, install the remaining fasteners as shown above and tighten to spec.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2013, 2015 Cequent Perfromance Products Inc. - Printed in Mexico
Installation Instructions
Mazda 6
Fascia
(Sold separately)
Drawbar Kit:
3594
Drawbar must be used in the
RISE position only.
Access hole
EXISTING HOLES
Tighten all 1/2" fasteners with torque wrench to 75 Lb.-Ft.(101 n*m)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, PC4
3 3 3 3 4 4 4 4
Access hole
3 3 3 3
Qty. (4)
NUT – 1/2-13 GR2
4 4 4 4
Qty. (4)
WASHER CONICAL– 1/2
Sheet 1 of 3
24908N
Part Numbers:
24908
60339
77295
1 1 1 1 2 2 2 2
Existing holes both sides
Fasteners are typical
For both sides
10-6-15
Form F206 Rev A 5605
Rev. B
Publicidad
Manuales relacionados para Cequent Performance Products 24908
Resumen de contenidos para Cequent Performance Products 24908
- Página 1 Installation Instructions Part Numbers: 24908 Mazda 6 Fascia 60339 (Sold separately) 77295 Drawbar Kit: 3594 Do Not Exceed Lower of Towing Vehicle Drawbar must be used in the Manufacturer’s Rating or RISE position only. 2000 LB (908 Kg) Max Gross Trailer Weight 200 LB (90.8 Kg) Max Tongue Weight...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Fiche 1 de 3 24908N 10-6-15 Rev. B z 2013, 2015 Cequent Performance Products, Inc. - Imprimé au Mexique Formulaire F206 Rév A 5605...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 1 de 3 24908N 10-6-15 Rev. B z 2013, 2015 Cequent Performance Products, Inc. - Imprimé au Mexique Form F206 Rev A 5605...