Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75210F
Wrenches: 18mm, 3/4
Drill Bits: None
Fasteners Typical
Both Sides
kj
j
½-13 x 4" Hex Bolt
Qty. (8)
k
Qty. (8)
½ Flat Washer
For vehicles without factory step bumper, skip down to step 2.
1.
Remove fasteners which attach bumper mounting bracket to vehicle frame, one each side, and discard (see Figure 2).
2.
Raise hitch into position and secure with fasteners provided with hitch as shown in Figure 1. Tighten all ½-13 GR5 fasteners
with torque wrench to 75 lb.-ft.
Note: On vehicles with factory step bumper, bumper mounting bracket will be re-attached at original position with fasteners
provided with hitch.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
2005, 2014 Cequent Performance Products, Inc. – Printed in México
©
Installation Instructions
Dodge Sprinter
Freightliner Sprinter
Vehicle Frame
Figure 1
Tighten all ½-13 GR5 fasteners with torque wrench to 75 lb.-ft. (102 N*M)
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV3, SUV4
Remove fastener
And discard
Step Bumper
Mounting Bracket
l
Qty. (8)
½ Conical Toothed Washer
m
Qty. (8)
½-13 Hex Nut
75210N
Part Numbers:
75210
44745
87647
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
7,500 (3,405 kg)
750 (341 kg)
5,000 (2,270 kg)
500 (227 kg)
Accessory Rating
ml
Figure 2
Removal of step bumper
Mounting fastener
06/16/2014
Rev. D
Form: F205 Rev A 5-6-05
C
Publicidad
Manuales relacionados para Cequent Performance Products 75210
Resumen de contenidos para Cequent Performance Products 75210
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2005, 2014 Cequent Performance Products, Inc. – Printed in México © Sheet 1 of 3...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2005, 2014 Cequent Performance Products, Inc. – Imprimé au Mexique ©...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. © 2005, 2014 Cequent Performance Products, Inc.– Impreso en México Hoja 3 de 3 75210N 06/16/2014 Rev.