Cequent Performance Products 24848 Instrucciones De Instalación

Frame Rail
Exhaust Hanger
Hitch Shown In Proper Position
Equipment Required: Utility Knife
Fastener Kit: 24848F
Wrenches: T-20, T-25 Torx Driver y,
13mm, 11/16" and Extension Driver
Drill Bits: 1/2"
Locating
Edge
Figure 2
1 1 1 1
Qty. (2) Bolt M8 X 1.25 X 55 CL 9.8
2 2 2 2 Qty. (2) Bolt, Carriage 7/16-14 X 1.50 GR 5
3 3 3 3 Qty. (2) Block ¼ X 1 X 3
1. Remove plastic fascia covering the passenger side frame rail of the vehicle by removing the (5) Torx screws. Return plastic fascia
covering and screws to vehicle owner. Remove the two plastic fascia nuts from the fascia tabs (Do not discard).
2. Remove the (2) bolts from the exhaust hanger bracket as shown in Figure 1 to lower the exhaust. Return bolts to owner.
3. Slide the driver's side bracket above the exhaust bracket. Note: Sandwiching the hitch bracket between frame and exhaust hanger bracket.
Using the (2) M8 bolts loosely tighten the fasteners. Note: Rotate the hitch for ease of installation.
4. Align the passenger bracket with the locating edge and the tab see Figure 2 (check hitch for alignment perpendicular of the vehicle
making sure the bracket is flat against the frame rail). The passenger side bracket may need to be pushed flat against the frame
rail. Then using the hitch as a template mark the hole locations. Drill the 1/2" holes.
Optional: Lower the hitch to drill (2) 1/2" hole into the frame rails. Repeat step 3.
5. Fishwire the passenger side fasteners through the access slot in the frame rail, through the side bracket of the hitch (rearward
attachment first) and install conical washers and hex nuts.
6. Trim the Fascia on the driver's side near the exhaust as needed. Obtain vehicle owners approval before cutting.
7. Reattach fascia tabs
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2009, 2011, 2012, 2015 Cequent Performance Products – Printed in Mexico
Installation Instructions
VW Passat (
Fascia
VW Passat Wagon (
Drawbar must be used in the
RISE position only.
Exhaust
Tab
Exhaust Hanger
Bracket
Fascia trim required. Obtain vehicle owners approval before cutting
Tighten all M8 X 1.25 CL9.8 fasteners with torque wrench to 20 Lb.-Ft. (27 N*M)
Tighten all 7/16-14 Gr. 5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Except 4Motion)
Except 4Motion)
VW CC
Note: Fascia trim required
(Sold separately)
Drawbar Kit:
3594
Frame Rail
Existing
Weld Nuts
1 1 1 1
1 1 1 1
Figure 1
Passenger Frame Rail
Cut-away for View
4 4 4 4
Qty. (2) Conical Washer 7/16"
5 5 5 5 Qty. (2) Nut 7/16-14
6 6 6 6 Qty. (1) Pull wire
Sheet 1 of 3
Part Numbers:
24831
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: Passat Sedan PC1, 2
Wagon PC1,2
CC- TBA
Fascia area to be trimmed,
depending on vehicle style
2 2 2 2
3 3 3 3
Tab
4 4 4 4
5 5 5 5
Locating
Edge
24848N 10-8-15
Form F206 Rev A 5605
24848
60264
77221
(U-HAUL)
Access Slot
6 6 6 6
Pull Wire
Drilled Holes
Rev. E