Cequent Performance Products 24855 Instrucciones De Instalación

Lower Body Panel
Vehicle Frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24855F
Wrenches: 10mm, 3/4", 11/16"
Drill Bits: None
Other Tools: Spray lubricant
Vehicle frame
cut-away to show detail
Bend Handle-Nut as
shown. Insert through
vehicle access slot
and align over hitch
attachment.
1
8
Bolt leader
1/2"-13 X 1-1/4" Gr.5 Hex Bolt
Qty. (2)
1
1/2" Conical Toothed Washer
Qty. (2)
2
1/2"-13 Handle Nut
Qty. (2)
3
7/16"-14 X 1-1/4" Gr.5 Carriage Bolt
Qty. (2)
4
1. Drop muffler by removing (2) rubber isolator hangers off of hanger rods. See next page for muffler heat shield removal and
trimming. After trimming then proceed with Steps 2-5 below.
Using Bolt Leaders insert 7/16" Carriage Bolts and Carriage Blocks into vehicle frame as shown above. Do this on both sides
2.
of vehicle before raising hitch into place.
3. Carefully raise hitch into place over muffler and up around bolts installed in Step 1 above, being careful not to push bolts back
up into frame. It helps to leave Bolt Leaders on bolts for this step. Be careful not to poke yourself with the ends of the Bolt
Leaders. Wear safety glasses always!
Install 7/16" Conical Washers and 7/16" Nuts on to bolts securely without tightening to hold hitch in place.
4.
Bend Handle Nuts as shown above and insert through access holes in frame and align over slots in hitch. Install 1/2" Conical
5.
Washers and 1/2" bolts. Torque fasteners to specs below and then raise muffler back in to place.
Tighten 1/2"-13 Gr.5 and 7/16"-14 Gr.5 bolts /nuts with torque wrench to 50Lb.-Ft. (68 N*M).
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
© 2010, 2011, 2015 Cequent Performance Products - Printed in Mexico
Bumper Fascia
(Sold separately)
Drawbar Kit:
3593
Drawbar must be used in
the RISE position only.
This is a magnified view of a Bolt Leader
for handle-nut
4
5
3
vehicle attachment slot and pull
2
6
7
Installation Instructions
Ford Fiesta 5-Door Hatchback
All Models
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Hitch type
Weight Carrying
Ball Mount
Access slot
Insert Bolt Leader through
block and screw on to bolt.
Then insert both through
back down through. Do this
before raising hitch into
position.
Note!
Muffler heat shield must be removed and trimmed
and reinstalled before installing hitch. See next page.
Qty. (2)
5
Qty. (2)
6
Qty. (2)
7
Qty. (2)
8
Sheet 1 of 6
Max Gross
Trailer WT (LB)
2000 (908 Kg)
Wiring Access Location: PC3, 4
Temporarily drop exhaust
by removing (2) rubber
isolator hangers from
muffler. It helps to spray
isolators with lubricant to
allow them to slip off of
holder more easily.
7/16" Carriage Block, 3/32" X 7/8" X 2"
7/16" Conical Toothed Washer
7/16" Hex Nut
7/16" Bolt Leader
24855N 10-07-15
Part Numbers:
24855
60271
77228
24847 U-Haul
Max Tongue
WT (LB)
200 (91 Kg)
Fasteners typical
both sides.
Rev. D
Form: F205 Rev A 5-6-05