Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Pullwire (provided)
Fastener Kit: 24843F
Wrenches: 11/16 & 9/16
1
2
98
Figure 2
1 1 1 1
Qty. (2)
Carriage bolt – 7/16-14 X 1-1/2" GR 5
2 2 2 2
Qty. (2)
Spacer
3 3 3 3
Qty. (2)
Flat washer 7/16"
4 4 4 4
Qty. (2)
Lock washer 7/16"
5 5 5 5
Qty. (2)
Hex nut 7/16-14
1.
Use pull wires to feed the carriage bolts and blocks into frame rails though access holes as shown. Leave pull wire attached.
2.
Raise hitch into position, feed pull wires thru adjacent holes in the hitch, remove pull wires and attach flat washers, lock
washer and nut, finger tight only (Be careful not to push fastener back into frame rail). Hand tighten only until all fasteners
are installed.
3.
Install remaining fasteners as shown above.
4.
Torque all fasteners to specifications.
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2009, 2011, 2012 Cequent Performance Products – Printed in México
Installation Instructions
Fascia
(Sold separately)
Drawbar Kit:
3594
Drawbar must be used in
the RISE position only.
3
4
5
76
Mazda 3 5-Door
Access holes
Existing hole
Tie down
hook
8 9
3
4
5
Figure 1
6 6 6 6
Qty. (2)
Hex bolt 3/8-16 X 2.00 GR5
7 7 7 7
Qty. (2)
Flat washer
8 8 8 8
Qty. (2)
Conical washer 3/8"
9 9 9 9
Qty. (2)
Hex nut 3/8-16
Sheet 1 of 3
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Wiring Access Location: PC3, 4
Fastener are typical
For both sides
1
2
7 6
24843N
10-8-15
Part Numbers:
24843
60259
77245
Rev. D
Form F206 Rev A 5605
Publicidad
Manuales relacionados para Cequent Performance Products 24843
Resumen de contenidos para Cequent Performance Products 24843
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. z 2009, 2011, 2012 Cequent Performance Products – Printed in México Sheet 1 of 3...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. z 2009, 2011, 2015 Cequent Performance Products – Imprimé au Mexique Feuille 2 de 3...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 24843N 10-8-15 Rev. D 2009, 2011, 2015 Cequent Performance Products – Impreso en México Form: F205 Rev A 5-6-05...