Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Lubricant or soapy water
Fastener Kit: 36525F
Wrenches: 10mm,17mm, small philips screwdriver
Drill Bits: None
Area to be trimmed.
Figure 2.
1 1 1 1
Qty. (4)
Bolt M10 x 1.25 x 30 CL8.8
1.
Loosen the spare tire for additional clearance during hitch installation.
2.
Remove the cover panels on both side of frame rails. Obtain owners permission to trim or return to owner. See Figure 2.
3.
Lower exhaust system at the rear rubber isolator leaving the rubber isolator in place on the vehicle. Spraying a lubricant or soapy water on the
metal hanger rod and the rubber isolator helps removal.
4.
Lift hitch into position, passengers side first. Place hitch over the top of the tail pipe. Rotate into position on the outside of the frame rail.
5.
Install fasteners as shown. Figure 1.
6.
Tighten all fasteners to required specification.
7.
Re-install appearance panels if trimmed.
8.
Reattach vehicle exhaust, spraying a lubricant or soapy water will help.
9.
Tighten spare tire back into position, if lowered.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
z
2012 Cequent Performance Products, Inc
Installation Instructions
Drawbar Kit:
36061
Drawbar must be used in the
Rise position only.
Existing
weld nuts
1 2
Figure 1.
Tighten all M10 CL 8.8 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M).
Kia Rondo
3500 LB (1589 Kg) Max Gross Trailer Weight
300 LB (136 Kg) Max Tongue Weight
Frame rail
2 2 2 2
Qty. (4)
Conical washer 3/8"
Sheet 1 of 3
36525N
Part Numbers:
36525
90220
06184
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Accessory Rating
Wiring Access Location:
2
1
11-30-12
Form F206 Rev B 9-17-2012
B
Rev. A
Publicidad
Manuales relacionados para Cequent Performance Products 36525
Resumen de contenidos para Cequent Performance Products 36525
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 36525N 11-30-12 Rev. A 2012 Cequent Performance Products, Inc Form F206 Rev B 9-17-2012...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2012 Cequent Performance Products, Inc Fiche 2 de 3...
- Página 3 Observe las precauciones de seguridad al trabajar por debajo del vehículo y use protección visual. No corte los orificios de acceso o accesorios con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. © 2012 Cequent Performance Products, Inc. Hoja 3 de 3 36525N 11-30-12 Rev.