LiftMaster 860LM Guia De Inicio Rapido página 2

PROGRAMMING
Each channel is compatible with a certain number of remote controls and
keypads. Refer to the list below:
• CH1: 50 remote controls and 2 keypads
• CH2: 20 remote controls and 2 keypads
• CH3: 20 remote controls and 2 keypads
When the channel has reached full capacity for remote controls, all LEDs
will blink 3 times. When the channel has reached full capacity for
keypads, all LEDs will blink 4 times. Additional accessories can be
programmed, however, the newly programmed accessory will replace the
first programmed accessory.
NOTE: This receiver will only allow you to program a button on the
remote control to one channel at a time. For example, if the button on the
remote control is already programmed to channel 1 and then is
programmed to channel 3, the button will be erased from channel 1 and
will only work on channel 3.
PROGRAM A SINGLE BUTTON REMOTE CONTROL
1. Press and release the Learn button for the selected channel on the
receiver. The corresponding LED will glow steadily for 30 seconds.
2. Within 30 seconds press and hold the button on the remote control
that you wish to program to the receiver.
3. Release the remote control button when the LED on the receiver
blinks, then turns off. Programming is complete.
Repeat the steps above for each remote control you would like to
program.
PROGRAM A 3-BUTTON REMOTE CONTROL AS OPEN, CLOSE,
AND STOP
1. Press and release the CH1 Learn button on the receiver.
2. Within 30 seconds press the desired OPEN button on the remote
control.
3. Press and release the CH2 Learn button on the receiver.
4. Within 30 seconds press the desired CLOSE button on the remote
control.
5. Press and release the CH3 Learn button on the receiver.
6. Within 30 seconds press the desired STOP button on the remote
control.
NOTE: If a remote control button is not pressed within 30 seconds, the
LED next to the selected Learn button will turn OFF. In that case, repeat
the programming.
TO ERASE THE MEMORY
Press and hold the Learn button for the channel you want to erase.
Release the button when the corresponding LED turns off; the memory
has been erased.
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:
1-800-528-2806
CH1 Learn Button
NOTE: The receiver can command the operator to close the door or gate
by constant pressure. This feature is only available with a wireless
control panel (Model 885LM). To enable this feature, press and hold the
push bar until the gate or door moves to the closed position.
Contact Rating . . . . . . . . . . . . . . . . . . . . . . 5 Amps 28 Vac or dc Max.
Power Rating . . . . . . . . . . . . . . . .9-30V AC or 9-34V DC, 50mA, 60Hz
RF Frequency . . . . . . . . . . . . . . . . . . . . . . . . . .310, 315, and 390 MHz
NOTE: If your operator does not meet the power specifications you
will need a Model 95LM transformer.
COMPATIBLE ACCESSORIES
Remote Controls . . . . . . . . . . Models 811LM, 813LM, 891LM, 893LM,
Keypads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Models 877LM, 877MAX
Wireless Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . Model 885LM
Antenna Extension Kits
15' Extension Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Model 86LM
25' Extension Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Model 86LMT
Antenna Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K77-36541
Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95LM
NOTICE: To comply with FCC and/or Industry Canada (IC) rules. adjustment or modifications of this
receiver are prohibited. THERE ARE NO USER SERVICEABLE PARTS.
This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
2
CH2 Learn Button
SPECIFICATIONS
890MAX, 893MAX, 895MAX, 892LT, 894LT
CH3 Learn Button