Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required: Pull wire ( Provided)
Fastener Kit: 51194F
Wrenches: 7/8"
Drill Bits: 1" & 3/8"
D ill Bit
1" & 3/8"
(If tie down bracket present)
Rearward of vehicle
Driver's side frame rail
5-1/8"
3/8" Dia.
5/8"
Drill first
Access hole drill location
driver side frame rail with tie
down bracket
1
1
Qty. (4)
Qty (4)
Carriage Bolt 1/2 13 X 1 75
Carriage Bolt 1/2-13 X 1.75
2
Qty. (4)
Spacer
Note: If there is access holes to put the bolts & spacers into the frame rails from the end on both sides
there is no need to drill.
Note: Due to variation in tie down brackets, some interference with the end of frame access hole may
occur on driver's side. See Figure 1.
1.
Using the pull wire insert carriage bolt and spacer using the kink pull wire method (Figure 3) into the rearward holes of the
each frame rail. Leave pull wires attached. If interfere with tie down bracket exists see Figure 1.
2.
Feed pull wire through the slots in the hitch.
3.
Raise hitch into position and onto carriage bolts remove pull wire and attach conical washers and nuts. Hand tighten the
fasteners.
Note: Be careful not to push fasteners back into frame.
4.
Repeat using the pull wire to insert remaining carriage bolt and spacer into each frame rail using the same access holes as in
Step 1.
5.
Tighten all fasteners to listed specification.
6
6.
Paint any bare metal.
P i t
b
t l
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2010 Cequent Performance Products
Installation Instructions
Ford Escape,
Mercury Mariner,
Drawbar Kit:
36051
Drawbar must be used in the
DROP position only.
Drilled access hole
See Figure 1.
Impact bar
Optional installation
with tie down bracket.
1" Dia - Drill after
3/8" hole
Figure 1.
Note: Fasteners typical both sides
p
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
(Includes Hybrid)
(Includes Hybrid)
Mazda Tribute
Do Not Exceed Lower of Towing Vehicle
Do Not Exceed Lower of Towing Vehicle
3500 LB (1589 Kg) Max Gross Trailer Weight
300 LB (136 Kg) Max Tongue Weight
Wiring Access Location: SUV1, SUV2
Rearward hole
Figure 2.
3
3
Qty (4)
Qty. (4)
Conical Washer
Conical Washer
4
Qty. (4)
Hex Nut 1/2-13
Sheet 1 of 3
Manufacturer's Rating or
1
2
2
43
g
51194N
4-28-10
Form F206 Rev A 5605
Part Numbers:
51194
End of frame
access hole
passenger side.
*Check driver's
side frame.
Kink pull wire to
keep block
independent of bolt
Figure 3.
Rev. A
Publicidad
Manuales relacionados para Cequent 51194
Resumen de contenidos para Cequent 51194
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2010 Cequent Performance Products Sheet 1 of 3 51194N 4-28-10 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2010 Cequent Performance Products Feuille 2 de 3 51194N 4-28-10 Rev.
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 51194N 4-28-10 Rev. A 2010 Cequent Performance Products Form F206 Rev A 5605...