Electrical Connections To Be Made - AERMEC TRS 1001DX Manual Del Usuario

ELECTRICAL CONNECTIONS TO BE MADE

1. Open the electric control box:
Remove the metal cover panel by loosening the 4 screws at the front;
2. Connect the power supply:
the unit must be powered with a voltage of 220-240V~50Hz / 208-230V~60Hz,
connecting the relative input cables to the XT1 control board;
WARNING: the power line must be suitably protected by appropriate circuit brea-
kers;
3. Connect the WRC1 panel:
To use the unit, connect the WRC1 control panel; this control panel must be con-
nected to terminals H1 & H2 on the XT2 control board.
A
D1 D2
Item
A
Outdoor unit
B
TRS1001DX
H1 H2
C
WRC1 Control Panel
D1 D2
H1 H2
D
Terminating resistor
The wired Panel can manage two types of incoming signal from the control device: 100-240V
Depending on the type of signal, the control device must be appropriately connected to the wired panel, as show in the following layouts:
WRC1 (2) WRC1 (1)
WRC1 (2) WRC1 (1)
100-240V~50/60Hz
D1 D2
100-240V~50/60Hz
100-240V~50/60Hz
100-240V~50/60Hz
120Ω
H1 H2
32
TRS1001DX
120Ω
D1 D2
B
D
H1 H2
C D1 D2
D1 D2
WRC1(1)
D1 D2
D1 D2 WARNING: for more information about length limits and types of installation for the connection cable, refer to the wired
panel manual;
• The cable must be two-pole twisted and insulated;
D1 D2
• If the unit is installed in a location with significant electromagnetic interference, it is advisable to use a screened cable
• Use a two-pole cable having a minimum cross-section of 0.75 ~ 1.25mm
• The maximum length of the connection is 250m;
H1 H2
Gate control
100-240 V
Gate control
N
D1 D2 L
100-240 V
N
L
Connecting the wired panel to the external contact with 100-240V
H1 H2
Gate control
5-24 V
Gate control
5-24 V
D1 D2
Connecting the wired panel to the external contact with 5-24V
NOTE
Refer to the wiring diagram in this manual.
WARNING:
• If a serial connection cable with a section of more than 1mm
used, the total length can be up to 1500m (otherwise, the limit
is 1000m);
• The cable must be two-pole twisted and insulated;
• If the unit is installed in a location with significant electromag-
netic interference, it is advisable to use a screened cable
• The minimum recommended cross-section is 0.75mm
D1 D2
Notes
---
D1 D2
The terminals are on the XT2 control board of the control box
D1 D2
D1 D2
H1 H2
Supplied as standard with the outdoor unit
H1 H2
H1 H2
(50/60Hz) or 5-24V
AC
WRC1
WRC1
AC
N H1
D1 D2 L H2
AC
N H1
L H2
WRC1
H1 H2
WRC1
DC
VCC H1
GND H2
DC
VCC H1
GND H2
D1 D2
H1 H2
D1 D2
H1 H2
D1 D2
D1 D2
D1 D2
;
2
H1 H2
H1 H2
H1 H2
DC
H1
D1 D2 H2
H1
H2
signal
AC
H1 H2
H1
H2
H1
H2
signal
DC
H1 H2
is
2
2
120Ω
D1 D2
H1 H2
120Ω
D1 D2