Use; Dry-Boil Protection; Cleaning And Maintenance - FAR BSF ST16 CI Manual De Instrucciones

ENGLISH

USE

1. To fill the kettle with water, remove it from its base, open its lid by pressing the
button on the lid, then pour the desired quantity of water into the kettle. Always
fill the kettle between the minimum (0.5 l) and maximum (1.7 l) marks. If there is
not enough water in the kettle, it will turn off before the water has boiled.
NOTE: Never exceed the maximum mark when you fill the kettle, otherwise there
is a risk of splashing of boiling water through the spout. Make sure that the lid is
securely closed before connecting the power cord to an electrical outlet.
2. Close the lid. Place the kettle on its base. Make sure the kettle is completely in
contact with the power base.
3. Function buttons
3.1 Instructions for use
This product is a fully automated electronically controlled
kettle. It allows water to be boiled to at the selected
temperature and kept warm. The function buttons are
positioned on the handle, they includes: the ON/OFF
button, the SET button, the KEEP WARM button,
LEDs indicating the temperature of the water and
the mode, a power indicator, a keep warm indicator, 6
temperature setting indicators "40 °C", "60 °C", "70 °C",
"80 °C", "90 °C, "100 °C". Press the ON / OFF button,
the button's red LED lights up to show that the appliance
is on. When the water is heating, the red temperature
LED lights up to show the temperature set. When keep
warm function is activated, the red KEEP WARM
button lights up. After keeping the water warm for half
an hour, the appliance automatically turns off. You can
also turn it off before that by pressing the ON/OFF button. The appliance has a
memory function.
3.2 Electronic control program and instructions:
3.2.1 Fill the appliance with an appropriate amount of water (0.5 L ~ 1.7 L), plug in
the appliance, it goes into standby and all the LEDs remain off.
3.2.2 Press the ON/OFF button, the red light on the ON/OFF button and the 100
°C temperature button light up. If you do not press any of the temperature setting
buttons, the appliance heat the water to 100 °C. Once the water boils, it turns off
automatically without activating the keep warm and all the lights turn off.
3.2.3 When the appliance is plugged in, you can select the temperature at "40 °C",
"60 °C", "70 °C", "80 °C", "90 °C", or "100 °C" by repeatedly pressing the SET
button, the corresponding LED will light up. There must be at least 3 seconds
between each time you press the button, if the interval is less than 3 seconds, the
setting will not work. The last temperature selected becomes the set temperature.
GB-8
40ºC 60ºC
70ºC 80ºC
90ºC 100ºC
KEEP
SET
WARM
When the water is not at the set temperature, the kettle heats the water until it
reaches the set temperature, then it automatically stops heating, all the lights go
out and it turns off.
3.2.4 When the kettle is in operating mode 3.2.2 / 3.2.3, press the KEEP WARM
button to activate the keep warm function, the KEEP WARM light turns on.
The keep warm temperature is the temperature that has been set. When the
water in the kettle has reached the set temperature, the KEEP WARM light
turns on to show that this function has been activated. The keep warm time is
half an hour. After half an hour, the appliance automatically turns off as does the
LED. Note: The appliance automatically activates the keep warm function when
the temperature of 100 °C is selected. The keep warm function is triggered when
the water temperature drops to 90 °C (the light goes off when the temperature
reaches 100 °C and it turns on again when the temperature drops to 90 °C). The
keep warm function remains active for half an hour.
3.2.5 If you press the KEEP WARM button after the keep warm function has been
activated, it deactivates this function and the light goes out. Go to chapter 3.2.3.
3.2.6 If you press the ON / OFF button (on / off ) when the appliance is on, it turns
off. To turn it on again, press this button again. All previous settings are cancelled.
3.2.7 Kettle memory function. If the kettle is removed from its power base and then
put back on within 90 seconds, the keep warm function remains active (it does
not need to be reactivated).

DRY-BOIL PROTECTION

If you inadvertently use the kettle with no water in it, the dry-boil protection system
will automatically switch it off. If this happens, leave the kettle to cool down before
filling it with cold water and boiling it.

CLEANING AND MAINTENANCE

Before cleaning the kettle, always unplug it from
the electrical outlet and wait until it has cooled
completely.
Never immerse the kettle or its power cord in
water and make sure that they never come into
contact with water.
ENGLISH
GB-9