Descargar Imprimir esta página
ESAB R-50 Serie Instrucciones
ESAB R-50 Serie Instrucciones

ESAB R-50 Serie Instrucciones

Reguladores de cilindro de flujo controlado

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

INSTRUCTIONS for
CONTROLLED FLOW CYLINDER REGULATORS
Regulator
Model
R-50-TIG-580
R-50-MIG-580
R-50-MIG-320
CGA-032 (FORMERLY "B"I.G.)—5/8—18RH female.
Each regulator is equipped with 1.50" (38 mm) dia., 0 - 4000 psi (0 - 276 bars) cylinder pressure gauge.
Dimensions Weight:
Accessory: CO
Heater, P/N 950578 - Recommended if CO
2
connects between regulator and cylinder permitting the CO
Requires standard electrical extension cord of appropriate length with 3-prong connections.
The INSTRUCTIONS contained on this sheet are intended specifically for operators who know the general
principles of operation and safe practices to be followed in operating this type of equipment. If you are not
sure that you understand these principles fully, we urge you to read our booklet "Precautions and Safe Prac-
tices for Arc Welding, Cutting and Gouging" Form 52-529, in addition to these instructions. Do NOT permit
untrained persons to install, operate, or maintain this equipment. Do NOT attempt to install or operate this
equipment until you have read and fully understand these instructions. If you do not fully understand these
instructions, contact your supplier for further information.
The regulators covered by these Instructions are listed by Underwriter's Laboratories only when using parts
manufactured by The ESAB Group to the specifications on file with Underwriter's Laboratories, Inc., and the
gas service for which it is designed and listed. The use of other parts voids the manufacturer's warranty.
Do not clamp regulator cap in a vise or grip it with a pair of pliers. Distortion of cap can jam the internal parts
and cause excessively high delivery pressure as well as weaken the threaded joint to the regulator body. This
may cause cap to fly off and possibly injure personnel in area.
The regulators are not adjustable. They are factory set to deliver a fixed flow rate as specified in the table
above. Do not attempt to make any adjustments.
Be sure this information reaches the operator.
You can get extra copies through your supplier.
R-50 SERIES
Part
Gas
Number
Service
18361
Argon
17773
Argon Mix
17774
CO
Overall length ................................4.25" to 4.75" (108 mm to 120 mm)
Body Diameter ....................................................................... 1.25" (32 mm)
Weight ...................................................................................1.00 lb. (0.45 kg)
CAUTION
Preset Nom.
Flow Rate
25 cfh (0.71 m
35 cfh (0.99 m
35 cfh (0.99 m
2
regulator is expected to operate at high duty cycles. The heater
2
to flow without "freezing up" the regulator.
2
Connections (CGA)
Inlet
/hr.)
580
3
/hr.)
580
3
/hr.)
320
3
F14-237
April, 2007
Outlet•
032
032
032

Publicidad

loading

Resumen de contenidos para ESAB R-50 Serie

  • Página 1 The regulators covered by these Instructions are listed by Underwriter's Laboratories only when using parts manufactured by The ESAB Group to the specifications on file with Underwriter's Laboratories, Inc., and the gas service for which it is designed and listed. The use of other parts voids the manufacturer's warranty.
  • Página 2 IMPORTANT: Before starting operation, test all con- to your distributor or to ESAB Remanufacturing Center, nections with a Leak Test Solution 411 S. Ebenezer Road, Florence, SC 29501. such as P/N 998771. Correct any leaks before starting work.
  • Página 3 Les détendeurs couverts par ces directives font partie de la liste des Underwriter’s Laboratories, et ce, uniquement lorsqu’ils utilisent des pièces manufacturées par le Groupe ESAB, selon les spécifications au dossier des Underwriter’s Laboratories Inc., et qu’ils sont manufacturés pour le service des gaz pour lesquels ils ont été...
  • Página 4 Tenez-vous toujours de côté. service et l’expédier chez votre distributeur ou au ESAB Remanufacturing Center, 411 S. Ebenezer Road, Florence, IMPORTANT : Avant de commencer le travail, vérifiez tous SC 29501 USA.
  • Página 5: Reguladores De Cilindro De Fluxo Controlado Série R-50

    Os reguladores tratados nestas instruções são registrados pela Underwriter’s Laboratories apenas quando se usam peças fabricadas por The ESAB Group de acordo com as especificações arquivadas na Underwriter’s Laboratories, Inc. e o serviço de gás para o qual foi projetado e indicado. O uso de outras peças anula a garantia do fabricante.
  • Página 6 Fique sempre de lado. regulador deve ser devolvido ao distribuidor ou ao ESAB IMPORTANTE: Antes de iniciar a operação, teste todas Remanufacturing Center, 411 S. Ebenezer Road, Florence, as conexões com uma solução para...
  • Página 7: Reguladores De Cilindro De Flujo Controlado Serie R-50

    Los reguladores cubiertos por estas instrucciones se enlistan en Underwriter’s Laboratories sólo cuando utilicen partes fabricadas por el Grupo Esab para las especificaciones en archivo con Underwriter’s Laboratorios, Inc. y el servicio de gas para el cual se diseñó y se enlistó. El uso de otras partes anula la garantía del fabricante.
  • Página 8 Párese siempre a un lado. El regulador se debe devolver al distribuidor o al Centro de remanufactura de ESAB en Center, 411 S. Ebenezer IMPORTANTE: Antes de comenzar la operación, pruebe Road, Florence, SC 29501 si el gas se está escapando a todas las conexiones con una solución...

Este manual también es adecuado para:

R-50-tig-580R-50-mig-580R-50-mig-320183611777317774