Auta 754105 Manual Del Usuario página 5

LLAMADA A TODOS. Con el mango colgado, dejar pulsada la tecla LLAVE durante 2s. El LED AZUL parpadeará rápidamente y se emitirá un
o
tono agudo. Al descolgar el mango, el LED_VERDE verde también iniciará un parpadeo rápido y se realiza una llamada a todos los
teléfonos/monitores de intercomunicación. El display mostrará un "*", que cambiará al código del dispositivo que en su momento
descuelgue.
Si ya hemos pulsado la tecla LLAVE durante 2s y queremos volver a la situación de reposo sin realizar ninguna llamada, podemo s descolgar y
o
colgar rápidamente o simplemente esperar 30s. El LED AZUL debe volver a su posición de encendido fijo.
· Recibir:
Con el mango colgado, el MONITOR podrá recibir llamadas. Se encenderá el display, indicando el TFNO/MONITOR que llama, sonará un
o
timbrazo especial de intercomunicación durante un máximo de 30s y el LED AZUL parpadeará rápidamente. Podremos interrumpir la
llamada con la tecla AUTO o descolgar para iniciar la conversación. Al descolgar el mango, el LED_AZUL y el LED VERDE parpadearán más
lentamente y tendremos al menos 90s de conversación. Este tiempo se prolongará indefinidamente, hasta que un tercero trate de llamar, lo
cual provocará que finalice en pocos segundos nuestro tiempo de conversación. Esto se indicará con un pitido y mostrando el c ódigo del
que intenta hacer uso de la línea en el display.
SÍMBOLOS EN PANTALLA - SYMBOLS ON SCREEN
Comunicación con placa
Communication with panel
Apertura de puerta
Door opening
Conversación
Conversation
COMPACT INTERCOM MONITOR WITH KEYBOARD AND DISPLAY
Features:
- What is the COMPACT INTERCOM MONITOR WITH STANDARD HANDSET ( MONITOR)?
It is a standard digital monitor that, besides being able to communicate with panels and switchboards; it can also perform voice
o
intercommunication with up to 15 other intercom devices (TELEPHONE/MONITOR) connected at the same bus.
- "Enable/Disable" Self-Starting configuration Jumper (J1).
If the jumper of J1 is removed or it is in 1-2 position, the self-starting will be enabled. If it is in 2-3 position, it will be disabled. The
o
self-starting can also be disabled for the entire installation form the panel.
- "MASTER/SLAVE" Configuration Jumper (J2).
There can only be a MASTER device sharing the same bus. The rest must be SLAVES. If the jumper of J1 is removed or it is in 2-3
o
position, the device will be set as MASTER. If it is in 1-2 position, it will be SLAVE. The facility will not work at all if there isn't any
MASTER device or even if there is more than one device set as MASTER.
- MONITOR ID for "Panel Calls".
The MONITOR always responds to calls made from the panels to the code 1 except if SWITCH-5 is ON. In this case, the MONITOR will
o
respond to calls made from panels to code 2.
- INTERCOMMUNICATION ID (switches from 1 to 4 of SW1).
It is possible to codify addresses from 1 to 15, using the first 4 switches of the SW2
o
- Options (switches from 5 to 8 of SW1).
Switch 5. As mentioned above, if it is activated (down), this device will respond to panel calls to code 2.
o
Switch 6. Only Intercom. If it is activated (down), this will be only an intercom device. It will not be able to communicate with neither
o
panels nor switchboards.
Switch 7. Only Reception. If it is activated (down), this device will not be able to initiate any intercom calls. It will only be able to
o
respond to them.
Switch 8. Priority device. If it is activated (down), this device will end any current conversation, setting the line free to perform any
o
new call.
- MULTITONE Configuration (Up to 7 different melodies).
Pressing C with the MONITOR hung up; we can select the desired ringtone.
o
- RINGTONES VOLUME Configuration (2 levels).
Pressing B we can select the ringtones volume.
o
- Setting The NUMBER OF RINGTONES and the ELECTRONIC CALL EXTENSION (0 to 4 ringtones)
See Table 1.
o
- Setting AUXILIARY OUTPUT (1 second pulse or TOGGLE)
See Table 1.
o
- ID=0: EVERY MONITOR CODIFY WITH ID=0, will always make a "General Call" with just one touch of the (KEY button) + pick the handset up.
- CONVERSATION LENGTH : Minimum 90s. From here, the conversation can continue indefinitely, unless a third party wants to use the line, which
will cause both devices will go to its standby mode. This is indicated by a short tone in the speaker during the conversation.
- CALLS CANNOT BE RECEIVED if the handset is picked up.
MONITOR COMPACT DIGITAL INTERCOM CON TECLADO
Llamada intercom
Intercom call
introducir código
Enter code
Llamada conserje
Switchboard call