GE 15142 Manual De Instrucciones

Outdoor Digital Timer
+ Button
Sets Auto ON/OFF options in clock mode.
Scrolls up through options in settings mode.
RCL Button
Turns ON/OFF Daylight Savings feature in
clock mode.
Cancels countdown setting when on.
When programming, press to clear settings.
Reset
Press and hold with toothpick or pencil to
clear all settings.
Install Set Up
1. If the time screen is completely blank it will need to be plugged into an outlet and charged for four
hours before programming can begin. If the screen is displaying numbers, it is ready to
be programmed.
2. Before programming, all settings should be reset. The reset button is located just above the "MENU"
button and is identified by "RESET". Use a toothpick or pencil to push the "RESET" button. Once
pushed the screen will show the display below on the screen. See Diagram A
Diagram A
AM MO TU WE TH FR SA SU
88:88
PM
RND
PROG
CTD
18 88
After a few seconds
AUTO ON OFF
+ 1h
Current Time Setting
1. The timer's default mode setting is clock mode. This will display the current time and day of the
week. See Diagram B
2. In clock mode, press and hold "OK" for 2 seconds to put the timer in clock setting mode.
3. The day will begin to flash on the display. Press "+" or "-" to select the current day and press
"OK" to confirm.
4. The hour will begin to flash on the display. Press "+" or "-" to adjust the hour and press "OK" to
confirm. Take note of the AM/PM setting in the upper left corner of the display.
5. The minute will begin to flash on the display. Press "+" or "-" to adjust the minutes and press
"OK" to confirm.
6. Press "MENU" to finish setting the clock and return to clock mode.
Note: If there is over 2 minutes of inactivity, the timer will automatically exit clock setting mode and
return to the clock mode.
Programming the On/Off Times
1. In clock mode, press "MENU" to put the timer in program setting mode. "1 On" will begin to flash.
This indicates that the timer is ready to program the "1 On" setting.
- "1": Indicates program group number (Note: total of 16 program groups)
- "On": Indicates when the program will power the devices On.
- "Off": Indicates when the program will power the devices Off.
2. To select program group and power on/off status, press "+" or "-" to cycle through all the program
groups. Press "OK" for the desired program group and ON/OFF status. Next, set the day(s),
hour and minutes.
3. The week will begin to flash on the display. Press "+" or "-" to select the day and press
"OK" to confirm.
Day Group Options:
MO TU WE TH FR SA SU ->
MO -> TU -> WE -> TH -> FR -> SA -> SU ->
MO WE FR ->
TU TH SA ->
SA SU ->
MO TU WE ->
TH FR SA ->
MO TU WE TH FR ->
MO TU WE TH FR SA ->
4. The hour will begin to flash on the display. Press "+" or "-" to adjust the hour and press "OK" to
confirm - Take note of the AM/PM setting in the upper left corner of the display.
5. The minute will begin to flash on the display. Press "+" or "-" to adjust the minutes and press
"OK" to confirm.
6. "1 On" will begin blinking. Push the "+" to begin setting "1 Off".
7. Go back to Step 3 and complete the same steps for settings Programs 1-16.
8. Once all programs are complete press "MENU" twice to exit program setting mode.
RCL (Recall) Setting
1. Press the "MENU" button and select the On/Off setting that needs to be changed
2. Press the "RCL" button to reset the current On/Off setting.
Switch Mode Indication
The switch mode is shown in the display during clock mode as "ON", "AUTO ON", "OFF", or "AUTO OFF"
together with the time of day. In normal clock mode, use the "+" button to adjust this to the desired
setting. This can be used to override the timer as explained in Diagram C.
Diagram C
AUTO OFF ON AUTO ON
ON = Always ON
OFF = Always OFF;
AUTO ON = Timer is activated and lamp/device is on.
The timer will follow the next off program.
AUTO OFF = Timer is activated and lamp/device is off.
The timer will follow the next on program.
Troubleshooting
Problem
Light or appliance does not turn ON.
Light turns ON/OFF at day instead of night.
AM MO TU WE TH FR SA SU
88:88
PM
RND
PROG
18 88
AUTO ON OFF
+ 1h
MENU
Diagram B
AM
PROG
AUTO OFF
OFF
Solution
Make sure light/appliance power switch is in ON position. Make sure timer
is in AUTO mode. If timer is in OFF mode the program is not running.
Check to make sure AM/PM time and program settings are correct.
Display (Shown in standard "clock mode")
- Button
Turns ON/OFF random setting in clock mode.
CTD
Scrolls back down through options in settings mode.
OK Button
Press and hold to set current time and day
Confirms choices through setting options
and goes to next option
Menu Button
Toggles to programming, countdown and clock
mode display screens.
DST-Daylight Savings Time Setting
1. In clock mode, press "RCL" to activate Daylight Savings Time. "+1H"will show on the display and the
clock will advance 1 hour forward.
2. Press "RCL" again to deactivate Daylight Savings Time. "+1H" will disappear from the display and
the clock will revert back to normal.
Random Security Option (RND)
Rnd program feature will turn lights On and Off using the programmed times + or - 30 minutes, giving
the house a more lived in appearance while occupant is away.
1. In clock mode, press "-" to start Random function. "RND" shows on the display indicating timer is in
random mode.
2. To cancel random function, press "-" again. RND disappears from the display.
Countdown Setting
1. Press "MENU" twice while in Clock mode to enter into Countdown mode. "CTD" shows on the LCD.
Setting interval is from 99:59:59 to 00:00:01.
2. The hour will flash on the display. Press "+" or "-" to adjust the countdown hour and press "OK" to
confirm.
3. The minutes will begin to flash on the display. Press "+" or "-" to adjust the countdown minutes and
press "OK" to confirm.
4. The seconds will begin to flash on the display. Press "+" or "-" to adjust the countdown seconds and
press "OK" to confirm.
5. "CTD" flashes. This means countdown function is activated.
6. The Timer starts countdown at once. "CTD" flashes on display during the entire countdown period.
There are two functions of Countdown mode:
1. Countdown to turn power on: When the Timer is in ON or AUTO ON status in clock mode, entering
countdown mode changes the status to ON automatically. At the end of the preset countdown
period, power is turned off.
2. Countdown to turn power off: When the timer is in OFF or AUTO OFF status in clock mode, entering
countdown mode changes the status to OFF automatically. At the end of the preset countdown
period, power is turned on.
**Note: Timer works according to the priority level of programs as below:
Countdown>Manual ON/OFF>Random>Program Setting
If the countdown function was activated and the Manual ON/OFF doesn't work, you need to cancel
countdown function before activating the Manual ON/OFF function.
Power Back-Up
In the event of a power failure, the timer will retain its settings.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encour-
age to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada
Step-by-Step
Instructional Video
Scan code or visit:
http://goo.gl/Ed4mR
WARNING
Risk of electric shoc k Risk of fire
• Do not use with an • Do not use to control
extension cord appliances that contain
• Plug directly into a GFCI heating elements (cooking
protected electrical outle t appliances, heaters, irons,
• Unplug timer before etc.)
cleaning •Do not exceed electrical
• Fully insert plug ratings
• Keep children away • Ratings are for both outlets
combined
15142 Manual Version 2
06/11/2012