Care And Maintenance - Lutron WIDR 64 Guia De Inicio Rapido

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Lutron Roller 64 WIDR Pocket Mount Chassis Installation Guide
5
Mount the Shade
5.1 Drive Wires and Controls
At the drive end, turn the square mounting yoke so that the drive control buttons face downward,
allowing access to them from below the pocket. Route the EDU power and control cables through one
of the notches facing the front (room side) or rear (window side) as shown.
5.2 Verify the Idler Type
Idler
Gray Tube Flange
5.3 Hang the Shade
IMPORTANT: This procedure must be performed by 2 people, with one person supporting each end of the shade. If the sub-brackets are mounted in a location
that cannot be reached when standing on the floor, 2 ladders or lifts may also be required. It is recommended that all steps are reviewed by both installers
before proceeding.
The square mounting yoke at each end of the shade is designed to fit over the mounting tabs on the shade brackets. Each side features a notch. The top and bottom
of the yoke will engage the shade bracket mounting tabs, with the lower notch around the retaining screw.
A. Align the idler mounting yoke with the shade bracket mounting tabs, and fit the yoke around the tabs and behind the head of the retaining screw as shown.
VIEW FROM BELOW THE POCKET
some details omitted for clarity
B. Depress the spring-loaded idler by pressing the shade toward the idler bracket, then fit the drive-end mounting yoke over the tabs, and behind the head of the
retaining screw, on the drive end shade bracket.
IMPORTANT: Ensure the EDU wires are routed properly through the notch chosen in step 5.1. and are not pinched.
VIEW FROM BELOW THE POCKET
some details omitted for clarity
Lutron Electronics Co., Inc.
02/2020
7200 Suter Road
P/N 045843 Rev A
Coopersburg, PA 18036-1299, U.S.A.
Square
Mounting
Yoke
Route cables
through the
notch here
or here
IMPORTANT: The idler of a Roller 64 WIDR shade must have a gray
tube flange. If the tube flange is not gray, do not install the shade.
Contact Lutron for additional information.
F
or complete warranty information, refer to: www.lutron.com/TechnicalDocumentLibrary/Window Systems Warranty.pdf
6
Check and Secure the Shade
Shades are sized according to the bracket-to-bracket distance indicated
on the original order so that the spring loaded idler will be compressed
to 50% of its total travel when both ends of the shade are engaged in the
brackets. This ensures safe mounting and smooth, quiet operation. After
mounting the shade according to the steps in Section 5, verify the idler is
compressed to 50% of its total travel by measuring the idler-end light gap
as described in Step A below.
Buttons
A. With the shade in the brackets, measure and verify that the idler-end light gap,
Downward
measured from the end of the shade tube to the outer face of the Idler Bracket,
is 3/4 in (19 mm), ±
in (3 mm). Make bracket position adjustments to correct,
1
8
if necessary.
B. Verify that the installed shade system is level and centered on the window
opening. Make bracket position adjustments to correct, if necessary.
C. Using the hand screwdriver only, tighten the retaining screw at each end of the
shade to secure it. DO NOT overtighten.
VIEW FROM BELOW THE POCKET
7
Wiring and Power-Up
A. Follow the instructions in the enclosed document: Sivoia QS Basic Wiring and
Setup; P/N 045520 to complete the shade wiring and set limits.
B. Run the shade up and down several times and verify that no object interferes
with normal shade movement. Make additional adjustments as necessary to
correct any problems discovered.
8
Install the Optional Pocket Flap (if applicable)
Hang the pocket flap on the flap hanger as shown. Verify the flap does not
contact the fabric or interfere with shade movement.
NOTE: For tall shades with large fabric roll diameter, lowering the shade
will make it easier to install the pocket flap.
3/4 in (19 mm)

Care and Maintenance

O
After a product has been installed correctly by a qualified installer, there is no
mechanical upkeep required. In the event adjustments or repairs are needed,
the original provider of the systems should be notified. All adjustments and
repairs must be made by qualified personnel.
Fabrics can be periodically dusted in place using a feather duster or vacuum
with a soft brush attachment. For detailed fabric care information, refer
to www.lutronfabrics.com.
Worldwide Headquarters | USA
Lutron Electronics Co., Inc.
7200 Suter Road, Coopersburg, PA 18036-1299 USA
Toll Free: 1.800.LUTRON1 | Technical Support: 1.800.523.9466
Tel: 1.610.282.3800 | Fax: 1.610.282.3090
lutron.com/help | systemsupport@lutron.com
EEA
Lutron NL B.V.
Herengracht 466, 1017 CA, Amsterdam,
Netherlands (Importer)
United Kingdom
Lutron EA Ltd
125 Finsbury Pavement, 4th floor, London, EC2A 1NQ UK
Tel: +44.(0)20.7702.0657 | Fax: +44.(0)20.7480.6899
Technical Support: +44.(0)20.7680.4481
Freephone: 0800.282.107
Lutron, the Lutron logo, and Sivoia are trademarks of Lutron Electronics Co. Inc., registered in the U.S. and other countries.
Page 2
IMPORTANT: Ensure the upper
limit is set so that the bottom bar
is not drawn up into the pocket
or sub-brackets. Bottom bar(s)
must stay below the dotted line
as shown.

Publicidad

Tabla de contenido
loading

Tabla de contenido