Stanley QDC 200 Instrucciones De Instalación

INSTALLATION INSTRUCTIONS
This sheet covers 3 installation options; select appropriate installation.
Diagram measurements are not to scale.
Option A – Regular Arm Installation
SPEED ADJUSTING VALVES
MAIN ARM
DOOR CLOSER
FOREARM
(Right Hand Door)
Option A instructions: 1
two (2) locations on door frame to mount arm shoe.
3.
or 1/4-20 machine screws. Install adjustable forearm/arm shoe to frame using screws (a) or (b).
ING VALVES MUST BE POSITIONED TOWARD HINGE SIDE.
6.
Adjust length of forearm so that forearm is perpendicular to frame when assembled to preloaded main arm.S ecure forearm to main arm with screw/washer (f).
7.
Adjust door's closing speed and power, see page 4 for reference.
Option B – Top Jamb Installation
MAIN ARM
DOOR CLOSER
FOREARM
ARM SHOE
SPEED ADJUSTING VALVES
(Left Hand Door)
Option B Instructions: 1.
two (2) locations on door to mount arm shoe.
3.
for 1/4-20 machine screws. Install adjustable forearm/arm shoe to frame using screws (a) or (b).
ING VALVES MUST BE POSITIONED TOWARD HINGE SIDE.
6.
(e). Adjust length of forearm so that forearm is perpendicular to door when assembled to preloaded main arm. Secure forearm to main arm with screw/washer (f).
7.
Adjust door's closing speed and power, see page 4 for reference.
Option C – Parallel Arm Installation
MAIN ARM
FOREARM
PARALLEL
BRACKET
SPEED
ADJUSTING
VALVES
DOOR CLOSER
(Left Hand Door)
FOREARM
MAIN ARM
SPEED
ADJUSTING
VALVES
DOOR CLOSER
(Right Hand Door)
QDC 200
1
-3/8
(35)
3/4
(19)
ARM SHOE
A
Right hand door shown,
reverse measurements for
left hand door application.
Hinge or Pivot
. Using the measurements from diagram A, mark screw hole center locations. Mark four (4) location on door to mount door closer and
2.
Drill pilot holes in door and frame, 7/32" (5.5mm) diameter for wood, or #7 (.201" diameter) for all purpose screws
5.
Hinge or Pivot
Left hand door shown, reverse
measurements of right hand
door application.
A
3/4
1/2
(19)
(13)
Using the measurements from diagram B, mark screw hole center locations. Mark four (4) location on frame to mount door closer and
2.
Drill pilot holes in door and frame, drill 7/32" (5.5mm) diameter holes for wood screws or drill and tap #7 (.201" diameter)
5.
Install main arm to bottom pinion shaft, perpendicular to door. Secure tightly with arm screw/washer
Option C
measurements from diagram C, mark screw hole
center locations. Mark four (4) location on door to
mount door closer and four (4) locations on inside
frame to mount parallel bracket.
door and frame, drill 7/32" (5.5mm) diameter holes for
wood screws or drill and tap #7 (.201" diameter) for
1/4-20 machine screws.
frame using screws (g) or (h).
door using screws (c) or (d). SPEED ADJUSTING
VALVES MUST
HINGE SIDE.
shaft, indexing main arm mark "L" or "R with pinion flat
as shown in figure 1. Secure tightly with screw/washer
6.
(e). Remove arm shoe from forearm (see figure 2).
Install ROD end of forearm to bracket using the screw
7.
(i). With door closed, adjust length of forearm so
that the tip of the main arm is approximately 1-1/2"
(38mm) away from being parallel with door, when
connected to the forearm. Secure with screw/washer
8.
(f). Adjust door's closing speed and power, see
PARALLEL
page 4 for reference.
BRACKET
bottom of closer or install (optional) cover, using small
screws (j).
Figure 1
Left hand door
Machine X2 Wood X2
(a) (b)
Machine X4 Wood X4
(c) (d)
X1
(e) (f)
Diagram for Option A
5
-1/2
(140)
12
(304.8)
Door Opening
To 100°
101° to 130°
131° to 180°
4.
Install main arm to top pinion shaft, perpendicular to door. Secure tightly with arm screw/washer (e).
8.
Snap pinion cap over shaft at bottom of closer or install (optional) cover with small screws (j).
Diagram for Option B
Door Opening
To 100°
101° to 130°
131° to 180°
12
(304.8)
5
-1/2
(140)
4.
8.
Snap pinion cap over shaft at bottom of closer or install (optional) cover, using small screws (j).
Instructions: 1.
Using the
2.
Drill pilot holes in
3.
Install Parallel Bracket to
4.
Mount closer onto
BE POSITIONED AWAY FROM
5.
Place main arm on closer pinion
9.
Snap pinion cap over shaft at
1-
1/2
(38)
Main arm
1 of 4
Machine X4
(g)
Wood X4
(h)
Optional
cover
X1 screw.
X1
(i) (j)
X1
1
SPEED ADJUSTING VALVES
1
-3/4
(25.4)
(44.4)
ARM SHOE
Inches (mm)
Dim. A
7-1/2 (191)
(152)
6
4-1/2 (114)
Mount closer onto door using screws (c) or (d). SPEED ADJUST-
Inche s (mm)
Dim. A
7-1/2 (191)
6 (152)
4-1/2 (114)
1
-7/8
(48 )
SPEED ADJUSTING VALVES
1
-3/4
(Right Hand Door)
(44.4)
Mount closer onto frame using screws (c) or (d). SPEED ADJUST-
Diagram for Option C
A
1/2
(13)
7/16
(11)
B
3
-1/2
(89)
3/4
(19)
Door Opening
To 120°
121° to 180°
Hinge or Pivot
Figure 2
Right hand door
FOREARM
Main arm
Incorrect installation or
adjustment could
cause damage or injury.
Read and follow
instructions carefully.
MAIN ARM
DOOR CLOSER
FOREARM
(Left Hand Door)
MAIN ARM
DOOR CLOSER
FOREARM
ARM SHOE
2
-3/4
(70)
2
3/8
(50.8) (9.5)
reverse measurements
for a right hand door
Left hand door shown,
application.
12
(304.8)
Inches (mm)
Dim. A Dim. B
9-1/2 (241) 3-3/4 (95)
7 (178) 1-1/4 (32)
1
ARM SH O E
3
2