Litex Industries RCE-103LW Instrucciones De Instalación Y Funcionamiento

I. SAFETY PRECAUTIONS
A.
DANGER: HIGH VOLTAGE! Household electrical power can cause serious injury or death. Disconnect source of electrical
power to the ceiling fan by removing fuse or switching off circuit breaker. Make sure all electrical connections comply with local codes,
ordinances, the National Electrical Code, and ANSI/NFPA 70-1999. If you are unfamiliar with electrical wiring, please use a qualified
and licensed electrician.
B.
WARNING: To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with the remote control
receiver are designed to accept only one 12 gauge house wire and no more than two lead wires from the receiver. If your
house wire is larger than 12 gauge or there is more than one house wire to connect to the two receiver wires, consult an
electrician for the proper size wire connectors to use.
CAUTION:
C. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THE FAN
WITH ANY SOLID STATE SPEED CONTROL DEVICE OR CONTROL FAN SPEED WITH A FULL
RANGE DIMMER SWITCH.
D. Electrical source and fan must be 115/120 volts, 60 Hz.
Maximum fan motor amps: 1.25; Maximum light watts: 300 incandescent only.
II. INSTALLATION OF RECEIVER (Please refer to Figure 1 before continuing.)
Manually set fan speed control to HIGH via pull chain and set light to ON via pull chain.
A.
IMPORTANT:
Fan speed and light control will not be activated by remote if pull chains for fan and light
are not set to the HIGH and ON positions, respectively.
B. Disconnect source of electrical power to the ceiling fan by removing fuse or switching off circuit breaker.
C. Lower ceiling fan canopy from the mounting bracket.
D. Disconnect existing wiring between ceiling fan and supply at outlet box.
E. Lay the black antenna wire on top of the receiver and slide the
receiver (flat side up) into the mounting bracket (Figure 1).
F. Match up wire colors from outlet box with wires on receiver and then
insert wires from outlet box into the corresponding quick connect clips.
IMPORTANT: Wire colors must match before making connections. Use wire
connectors supplied when making connections between receiver and fan.
Make wiring connections as follows: (Figure 2)
CONNECT:
GREEN fan wire......................................................BARE supply wire
BLACK receiver wire (AC IN L)...............................BLACK supply wire (L)
WHITE receiver wire (AC IN N)...............................WHITE supply wire (N)
WHITE receiver wire (TO MOTOR N)......................WHITE fan wire (N)
BLACK receiver wire (TO MOTOR L)......................BLACK fan wire (L)
BLUE receiver wire (FOR LIGHT)............................BLUE light wire (from fan) (L)
Pull on each wire to make sure they have been inserted correctly in the quick
connect clips. Wrap each quick connect clip and wire connector separately with
electrical tape as an extra safety measure. If other fan or supply wires are different
colors than those mentioned, have this unit installed by a qualified electrician.
G. Push all connected wires up into outlet box. Make sure antenna rests outside of mounting bracket.
H. Re-install the canopy on the mounting bracket.
III. AUTOMATED LEARNING PROCESS/ACTIVATING CODE
CAUTION: The transmitter can be programmed to multiple receivers or fans. If this is not
desired, turn wall switch off to any other programmable receiver or fan.
A. Remove battery cover.
B. Install the 12-volt battery (included). *Important: If there is plastic on the battery, remove plastic from battery before installing the battery.
C. Restore electrical power. Within 30 seconds of restoring electrical power, press the "LEARN" button located in the battery compartment
for 3 seconds or until fan switches to MEDIUM speed. Test the light and fan functions to confirm the learning process is complete. (Figure 4)
D. Locate dimmer switch behind the "LEARN" button in the battery compartment. (Figure 4) Set dimmer switch to the "ON" (D) position only if
using incandescent bulbs. Set dimmer switch to "OFF" (O) position if using compact fluorescent bulbs. NOTE: Most compact fluorescent bulbs are
not compatible for use with dimmer controls.
E. Replace battery cover on transmitter. (Figure 4)
IV. TRANSMITTER--CARE AND OPERATION
A. Store the transmitter away from excess heat or humidity.
B. To prevent damage to transmitter, remove the battery if not used for long periods.
C. Operation buttons on the panel of the transmitter:
button for fan high speed
button for fan medium speed
button for fan low speed
button for fan speed off
button for light brightness and off
The light function is controlled by pressing the
increase or decrease light. Tap button quickly to turn light off or on. If you press
the button in excess of 0.7 second it becomes a dimmer. The light varies cyclically
in 8 seconds. The light button has auto resume, so the light will stay at the same
brightness as the last time it was turned off.
IMPORTANT:
Make sure that fan has been turned off at wall switch and then allow blades to
come to a complete stop before manually activating the reverse switch on the fan.
V. TROUBLESHOOTING GUIDE
A. Fails to operate:
1. Make sure there is power to the receiver.
2. Make sure receiver is wired correctly.
3. Make sure that the fan is set on the highest speed via pull chain.
4. Make sure light kit switch is turned on.
5. Make sure the battery in the transmitter is good.
6. The learning process between fan and transmitter may not have been successful. Turn power off,
remove battery cover and repeat Step C in Part III (Automated Learning Code) above.
B. Transmitter won't operate at distance:
If transmitter operates fan and light kit when up close, but not at 40 feet away, try placing the black
antenna wire higher and make sure the black antenna wire is visible.
GENERAL INFORMATION
This remote control is designed to separately control your ceiling fan speed and light brightness.
There are four buttons to control the fan speed. The light dimmer button controls the light.
INSTALLATION AND OPERATING INSTRUCTIONS
TO:
button. Hold button down to
19˚
CAUTION: FOR MOUNTING RECEIVER,CEILING
ANGLE SHALL NOT EXCEED 19 DEGREES
RECEIVER MODEL: MR76T
AC SUPPLY
BLACK
WHITE
AC IN (LIVE)
AC IN (NEUTRAL)
BLACK WHITE
BLUE BLUE
BLACK BLACK
WHITE WHITE
BARE GREEN
AC SUPPLY
Fig. 2
(front)
DIMMER
SWITCH
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
USE THE FAN WITH ANY SOLID STATE SPEED CONTROL DEVICE
OR CONTROL FAN SPEED WITH A FULL RANGE DIMMER SWITCH.
MODEL: RCE-103LW
20˚
and
Above
DOWNROD
Fig. 1
ANTENNA
RECEIVER
CAUTION: DO NOT USE
FAN SPEED CONTROL
IN CANOPIES WHERE
THE MOUNTING IS NOT
AS SHOWN IN FIGURE 3
OF THE INSTALLATION
INSTRUCTIONS
Fig. 3
12V Size A23
(back)
LEARN
BUTTON
TRANSMITTER
Fig. 4
CAUTION:
LITEX INDUSTRIES, LTD.
GRAND PRAIRIE, TX 75050
FOR CUSTOMER SERVICE CALL: 1-800-527-1292
MOUNTING
BRACKET
RECEIVER