Publicidad
Idiomas disponibles
Idiomas disponibles
SAFETY and GENERAL
INFORMATION
Save these instructions. For your safety read,
understand, and follow the information provided with
and on this stand before using. The owner and operator
of this equipment shall have an understanding of the
stand and safe operating procedures before attempting
to use. The owner and operator shall be aware that use
of this product may require special skills and knowledge.
Instructions and safety information shall be conveyed in
the operator's native language before use of these jack
stands is authorized. If any doubt exists as to the safe
and proper use of these stands, remove from service
immediately.
Inspect before each use. Do not use if broken,
bent, cracked, or damaged parts (including labels)
are noted. Any stand that appears damaged in any
way, operates abnormally or is missing parts, shall
be removed from service immediately. If you suspect
that the stand was subjected to a shock load (a load
dropped suddenly, unexpectedly upon it), immediately
discontinue use until the stand has been checked by a
factory authorized service center (contact distributor or
manufacturer for list of authorized service centers). It
is recommended that an annual inspection be done by
qualified personnel. Labels and owner's manuals are
available from manufacturer.
PRODUCT DESCRIPTION
Omega High Reach Supplementary Stand is designed
to help prevent the tipping/ rocking of a vehicle while the
vehicle is engaged on an automotive lift. For use ONLY
under a properly secured automotive lift. It is to be
used in pairs to stabilize a vehicle during service. It is
not intended to support the lifted load, only to stabilize
the load as work is being performed under a properly
secured lift. The rated capacity of this device is
intended to be used as a reference of the working load
that this stand is capable of sustaining. The working load
is NOT increased if used in pairs. The working load of a
pair of stands shall not be considered to be more than
the rated capacity of a single stand. The rated capacity
of this stand is 4000 lb.
!
NEVER use high reach supplementary stand
to support a vehicle! Use a pair to prevent
vehicle tipping/rocking while vehicle is on an automotive
lift.
Saddle Pad (1)
Pin (3)
(2) Saddle
Grease Fitting (5)
(4) Height Adjustment
Handle
Bearing (6)
(7) Column Tube
(9) Bolt
Lock Pin (8)
(10) Nut
(11) Upper Plate
(12) Lower Plate
Upper Link (14)
(13) Threaded
Column
Leg (15)
(16) Lower Link
Figure 1 - Model 33020 Components
Parts List for Model 33020:
Item
Part No.
Description
1
T455-00002-000
Saddle Pad
2
T455-00003-000
Saddle
3
*
Pin, D6x40mm
Height Adjustment
4
T455-00001-000
Handle
5
*
Grease Fitting
6
*
Bearing
7
T457-02000-000
Column Tube
8
T457-04000-000
Lock Pin
9
*
HCS M8X15
10
*
Nut, Hex M8
11
T457-00003-000
Upper Plate
12
T457-05000-000
Lower Plate
13
T457-03000-000
Threaded Column
14
T457-00002-000
Link, Upper
15
T457-01000-000
Leg
16
T457-00001-000
Link, Lower
(*)
T457-06000-000
Hardware Kit
2
SPECIFICATIONS
Model
Capacity
33020
ASSEMBLY
(refer to Fig. 1)
Before beginning assembly of product, make sure all
parts are present. Compare parts with package contents
listed in Figure1 & Parts List below.
Estimated Assembly Time: 15 minutes
Tools Required for Assembly: 8mm wrench, hammer
and punch are required for assembly (Not included).
1. Attach lower plate (12) and upper plate (11) to tripod
legs (15) using bolts & nuts (9 & 10) provided. Finger
tighten only. Make sure both plates are placed above
the screw hole.
2. Attach lower and upper links (14 & 16) using bolts and
nuts (9&10) provided. Do not use any tools to tighten.
3. Insert threaded column (13) into column tube (7).
4. Insert bearing (6) and height adjustment handle (4)
into threaded column (13).
5. Attach saddle (2) on top of the threaded column
(13) and use a hammer to punch the pin (3) into the
threaded column.
6. Insert the assembly of steps 4 and 5 through the
upper plate (11).
7. Insert the lock pin (8) to the bottom of the tube (7).
8. Tighten securely all the bolts and nuts.
Qty
1
1
BEFORE USE
1
1. Inspect stand before each use. Do not use if bent,
broken or cracked components are noted. Ensure
1
that all parts move freely.
1
2. Verify that the product and the application are
1
compatible, if in doubt call Omega technical service
1
(888)332-6419.
3. Before using this product, read the owner's manual
1
and familiarize yourself thoroughly with the
18
product and hazards associated with its improper
18
use.
1
4. Always check the vehicle owner's or service manual
1
for location of proper lift and support points. This
device is designed to stabilize, NOT SUPPORT a
1
vehicle while on an automotive lift. Special skills and
3
knowledge pertaining to working on and around an
3
automotive lift may be required before attempting to
3
position/use this device.
-
Base Dimensions
Min. Height
2 Ton
24" x 22-1/2"
69"
• Study, understand, and follow all printed
materials provided with/on this device before
use.
• Do not exceed rated capacity.
• Use only on hard, level surface.
• Center load on saddle.
• Do not use the stand to support a vehicle or
stabilize vehicle.
• Use stands in pairs under a properly secured
automotive lift to stabilize the vehicle before
starting repairs.
• Only attachments and/or adapters supplied by
the manufacturer shall be used.
• No alteration shall be made to this device.
• Failure to heed these markings may result in
personal injury and/or property damage.
OPERATION
!
WARNING Use only on areas of the vehicle as
specified by the vehicle manufacturer. Use
ONLY on vehicles whose contact points are compatible
with the saddles of these stands. Incompatibility may
result in structural damage to the vehicle and/or stand.
Structural damage to either may result in sudden and
unexpected loss of load height!
To Raise Saddle
1. Refer to the vehicle service manual or vehicle
manufacturer for location of proper lift and support
points. This device is designed to stabilize, NOT
SUPPORT a vehicle while on an automotive lift.
!
an automotive lift is required before attempting to
position/use this device.
2. Locate and turn the height adjustment handle
clockwise.
To Lower Saddle
!
Slowly turn height adjustment handle counter-clockwise.
Ensure vehicle is balanced and secure on the vehicle
lift before removing this device.
3
Max. Height
Saddle Size
78"
5-1/2" x 2"
!
WARNING
Special skills and knowledge pertaining to
working on, under, and around a vehicle on
Be sure all tools and personnel are clear
before lowering load.
Publicidad
