Chamberlain LiftMaster 395LM Security+ Guia De Inicio Rapido

Model 395LM Security ✚
Modèle N° 395LM Security ✚
Modelo 395LM Security ✚
Light Control Actuator
Commutateur de commande d'éclairage
Actuador de control de luz
Antenna
Antenne
Antena
Learn Button
Bouton LEARN
Botón "APRENDER" (Learn)
OWNER'S INSTRUCTIONS
The Remote Light Control is designed to operate lights
according to the rating chart shown. Please read the
instructions and power limitations carefully to ensure proper use
and maximum safety. NOT recommended for use with toasters,
coffee pots, florescent or halogen lighting systems.
The Light Control can be operated by any 315MHz
SECURITY✚ ® remote control and/or Keyless Entry.
The Remote Light Control receiver needs to learn the
remote control code. Follow the instructions below:
• Plug the light control into a 120Vac polarized outlet. The plug
contacts are designed for polarized outlets only.
• Press and release the "learn" button on the Light Control with
a pen or pencil tip. The learn indicator
light will glow steadily for 30 seconds.
• Within 30 seconds, press and hold the
button on the hand-held remote.
• Release the remote control push button.
Code setting is now complete.
The remote control push button must be held down until the
receiver indicator light flashes for the light control to learn the
remote control's code.
® Remote Light Control
®
Télecommande d'eclairage
®
Control Remoto de luz
Learn Indicator Light
Voyant indicateur d'apprentissage
Luz indicadora de aprendizaje
Select a
push button
WARNING
CAUTION
WARNING
To prevent possible SERIOUS INJURY or DEATH from electrocution
or fire, the light control is ONLY for indoor use.
CAUTION
AVERTISSEMENT AVERTISSEMENT
Pour éviter les risques de BLESSURE GRAVE ou de MORT causés
par l'électrocution ou l'incendie, la commande d'éclairage doit être
ATTENTION
utilisée UNIQUEMENT pour l'intérieur.
ADVERTENCIA ADVERTENCIA
AVERTISSEMENT
Para prevenir LESIONES GRAVES O LA MUERTE posibles de
electrocución o incendio, el control de luz es para uso interior
SOLAMENTE.
ATTENTION
ERASING CODES
If the receiver LEARN button is pressed and held until the
yellow indicator light alongside goes out (in about 6 seconds),
all memorized codes will be erased.
OPERATING INSTRUCTIONS
If two or more light controls are installed, they must be located
at least 10 feet apart to prevent electronic interference.
• First, plug the lamp into a wall outlet and turn it ON.
• With the lamp still in the ON position, plug it into polarized
outlet on the light control. Plug the Light Control into a 120Vac
polarized outlet. The bulb will not light.
• TO TEST: Press and release the light control actuator. The
light should turn ON. Press the remote control push button.
The light should turn OFF.
If the remote control does not activate the light, check to be sure:
• You are pressing the remote control push button selected to
operate the light control.
• The remote control battery has power. Refer to the remote
control instructions for battery changing information.
NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or
modifications of this receiver and/or transmitter are prohibited, except for changing the
code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Resistive Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Amps
Motor Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/3 HP
Incandescent Lamp . . . . . . . . . . . . . . . . . . . . . . . . .600 Watts
ENGLISH
RATING
A
PR