Operation Overview - PCL QUBE Manual De Iniciación

Operation Overview

The unit has a choice of 3 different inflator applications installed.
Your QUBE can be configured into the 3 different applications but
for some models only 1 mode may be present.
Application Modes:-
Standard (std)
The QUBE will inflate and deflate tyres (Default mode by PCL)
Tyre Shop (tir)
The QUBE will inflate and deflate tyres and will allow Over Pressure
Setting (OPS)
N2 (N2P)
The QUBE will inflate and deflate tyres and allow tyre purging for
Nitrogen rich tyre filling
During the start up procedure initiation the current application is
always shown.
Start-up
On plugging in the unit for the first time, the QUBE will
automatically start in Standard (Std) Operation.
However, if the Tyre Shop (tir) or N2 (N2P) Operation are
required, then follow the Application Mode Selection.
The QUBE will reboot into the desired application and will remain in
this mode until an alternative mode is selected with Application
Mode Selection.
Standard (Std) Operation
Inflation and deflation
1. Set desired pressure, by touching either
2. Connect the hose to the tyre.
3. Automatic inflation will commence to the set pressure,
periodically stopping to display the pressure of the tyre.
4. If the pressure in the tyre is below 3 psi, 0.2 bar or 20 kpa,
the process will not commence until
5. When the Set pressure is reached, the buzzer will sound
and the display will show 'END' with the final pressure.
6. Remove the hose from tyre.
7. For selection of alternative pressure unit touch
For adjustments to Inflators parameters
please refer to your Distributor or PCL.
This unit is not suitable for the filling of
bicycle tyres with a standard (Presta,
Woods) bicycle valves and adapters. Over
fill of the tyre is possible!
Application Mode Selection
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Tyre Shop (tir) Operation
Inflation and deflation
1.
2.
3.
4.
or
5.
6.
is touched.
To enable setting of OPS
1.
2.
3.
Note:
The OPS value will not be applied when the tyre has a pressure of
more than 3 psi, 0.2 bar, or 20 kpa.
To prevent the accidental use of OPS, the OPS setting is not
retained after the machine is powered down.
www.pclairtechnology.com
PCL ACCURA QUBE Tyre Inflator
Turn on power supply
Display will show all LCD digits check
Display will show the current Firmware version number e.g.
'.3.1.1'
Display will show Program model variant '300' ( psi default)
or '340' (bar default)
Display will show the current application, 'Std' , 'tir' or 'N2P'
as stored.
After 10 seconds the display will show 'PCL'
Touch to enter Application Mode
Display will show 'L 0', confirm to enter by touching
Display will show 'APP' confirm to enter by touching
Display will show 'Std' if this is the required Application
then exit Application mode by touching
To change to 'tir' or 'N2P' touch
And use to change back to 'Std'
Confirm the application 'Std', 'tir' or 'N2P' by touching
Display shows 'APP' exit the application by touching
twice.
The QUBE will reboot into the desired application and will
remain in this mode until an alternative application is
required.
Set desired pressure, by touching either
Connect the hose to the tyre
Automatic inflation will commence to the set pressure,
periodically stopping to display the pressure of the tyre.
If the pressure in the tyre is below 3 psi, 0.3 bar or 30 kpa,
the process will not commence until
When the Set pressure is reached, the buzzer will sound
and the display will show 'END' with the final pressure.
Remove the hose from tyre.
Touch and display will toggle 'OPS' and blank value
Increment the OPS value between 0-29 psi, 0-2 bar,
0-200 kpa, by touching and
touch
Display will revert to the Set pressure previously selected.
twice
or
is touched.
, to accept the value,