Publicidad
Idiomas disponibles
Idiomas disponibles
FLUSH MOUNTING DIGITAL TIME SWITCH
INSTRUCTIONS FOR USE
Menu access button /
Confirm flashing value
INSTALLATION
This device is designed for installing in a universal flush mounting box or surface
mounting box. Follow the next diagram:
RECOMMENDATIONS
The installation should be carried out by an officially authorised technician.
Do not install near inductive charges (motors, transformers...).
A separate power supply line is advisable (if necessary from a network filter).
RESET
When resetting, the device will restore the last valid settings before the power
supply was lost: time and date, programmes P1 to P20 and configuration of
parameters.
Regardless of the length of time the device is disconnected, the programmed
alarms and configuration parameters will be saved correctly.
The time and date will be saved for a period of approximately 24 hours, without any
type of power supply.
Following a period longer than this, the device will reset to 1 January 2006, 00:00
hours.
The device is reset by pressing the 4 buttons simultaneously.
After resetting the device the factory default settings are the following:
• Language: Spanish
• Time: 00:00 (24 hour mode)
• Date: 01/01/2006 – Sunday (winter)
• Daylight saving adjustment in spring: last Sunday in March at 2am
• Daylight saving adjustment in autumn: Last Sunday in October at 3am
• All programmes empty.
DEVICE FUNCTION
The device is programmed using the menus and sub-menus.
The values to be programmed will flash on the display.
The following information is displayed on the screen:
-
Day of the week.
-
Time and date.
-
Schedule of settings established for that day.
-
Status On/Off
-
Hand symbol (if activated).
-
"PERMANENT" will be displayed on the second line if it is activated.
C: Return to the previous option / switch between statuses:
-
PERMANENT: the programmes will not be carried out.
-
PROGRAMMED the device works normally and displays the schedule
assigned for the current day.
▲▼: Both buttons have the same function. They manually switch the activation
status of the channel: On/Off.
√ √ √ √ : Access the menu / Confirm the flashing value.
▲: Scroll up the menu / Increase the flashing value. If it is held down the value can
be increased faster, by 5 units per second
▼: Scroll down the menu / Decrease the flashing value. If it is held down the value
can be decreased faster, by 5 units per second.
PROGRAMMING OF SETTINGS
The device's 20 programmes can be set using this menu.
Each one can be seen by pressing the buttons ▲▼.
To access a specific programme simply press button √ √ √ √ .
The type of setting can be programmed:
-
On, Off
-
Start Random: the random period starts.
-
End Random: the random period ends.
DECO DATA
Button for returning
to previous option
Function selection
buttons
Metallic frame
Frame
2
1
4
L
N
L
N
The random periods (for presence simulation) carry out a change in the relay
activation status for periods between 30 minutes and 2 hours, from the start of the
period or as of the last relay switch.
Note: programming of any On/Off, manual switch or date/hour change carried out
whilst the random period is activated will cause the random period to end
immediately.
TIME ADJUSTMENT
The device's time can be set using this menu. The values to be configured include
(in this order): Year, month, day, day of the week, hour, minute.
Once MINUTE has been confirmed the display will automatically return to MAIN
MENU and the time and date will be saved.
LANGUAGE SELECTION
The language can be set using this menu, selecting between:
Spanish, English or Portuguese.
ADJUSTMENTS MENU
This menu accesses the more complex functions of the device, such as:
configuration of daylight saving changes, type of load, switch off mode and
programme deleting mode.
- SEASON sub-menu: In this menu the daylight savings changes can be set,
selecting between:
-
Automatic: switches to daylight saving at 2am on the last Sunday in
March and switches back at 3am on the last Sunday in October.
-
Manual: this allows the specific dates and times of the changes to be
established.
-
Disabled: daylight saving changes will not be made.
- STATUS sub-menu: Programmes can be switched off for a certain period of time
using this menu, without the need to delete the settings. The following options are
available:
-
OFF: the device remains switched off (everything works except the
programmes). The relay remains Off.
-
RANDOM: the device will only work with the random programmes. The
other programmes are ignored.
-
NUM DAYS: the timer programme will NOT function during the number of
programmed days between 1 and 31, (for example: holiday period).
-
ON: Any type of programme will function.
- DELETE sub-menu
All the programmes can be deleted.
- VERSION sub-menu
The firmware version of the device can be displayed quickly in this menu. Type:
INT V1.00.
TECHNICAL CHARACTERISTICS
Power supply:
Power supply tolerance:
Frequency:
Rupture capacity:
Internal consumption:
Temperature:
Recommended maximum loads:
Incandescent:
Non-compact fluorescent:
Compact fluorescent:
Low voltage halogens:
Halogens (230 Vac):
Energy saving lights:
Precision:
Type of protection:
Class of protection:
Directives:
Mark:
DIMENSIONS
93
60
ORBIS TECNOLOGIA ELECTRICA, S.A.
Lérida, 61
Teléfono: +34 91 5672277;
230 V~
± 10%
50 Hz.
8 (2) A / 250 V ac
16.5 VA Maximum capacitives (1.4 W).
From 0 ºC to +40 ºC
1,800 W
500 W
250 W
600 VA
1,500 W
140 W
≤ ± 1 s/24 h at 23 ºC using quartz crystal
IP 20 according to EN 60529
II according to EN 60335 fully installed
2002/95/EC (RoHS) 73/23/CEE and
93/68/CEE (Electrical Safety)
89/336/CEE and 92/31/CEE (CEM)
EC
45.5
31
A016.35.53585
E-28020 MADRID
Fax: +34 91 5714006
E-mail: info@ orbis.es
http://www.orbis.es
Publicidad
