Bayco 651 Instrucciones De Operación

Operating Instructions for
Model 651 13 Watt Fluorescent
Light on Retractable Reel
Multiple Patents Pending
Electrical Rating - All models use 125 Volts 60 HZ
CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK AND FIRE - PULL PLUG
WHEN SERVICING OR WHEN RE-LAMPING — USE ONLY 13 WATT OR SMALLER
BULB.
CAUTION
• DO NOT use this cord reel in explosive atmospheres, near fl ammable liquids, or
where explosion proof lamps are required.
• DO NOT use in the proximity of vehicles or equipment when there is a risk of
fl ammable liquids coming into contact with the hand lamp
• DO NOT immerse in water
• DO NOT use in areas where water can accumulate or in rain or mist
• CAUTION: Risk of Electric Shock – For Light Duty Dry Location Use Only
GENERAL USE CORD REEL ONLY. NOT FOR HARD USE. FOR INDOOR DRY
LOCATION USE ONLY FOR LIGHT DUTY RESIDENTIAL USE ONLY
WARNING: NOT FOR USE ABOVE HAZARDOUS LOCATIONS
CAUTION: DO NOT USE IN HAZARDOUS LOCATIONS AS REQUIRED BY THE
CANADIAN ELECTRICAL CODE, PART I
IMPORTANT SAFETY INSTRUCTIONS
This product has a polarized plug (one blade is wider than the other). As a safety feature, this
plug will fi t in a polarized outlet only one way. If the plug does not fi t fully in the outlet, reverse the
plug. If it still does not fi t, contact a qualifi ed electrician. Never use with an extension cord unless
the plug can be fully inserted. Do not attempt to defeat this safety feature.
• CAUTION: PULL OUT CORD TO FULL LENGTH WHEN USING RECEPTACLE
• CAUTION: DO NOT ALLOW THE CORD TO RETRACT BY ITSELF AS DAMAGE
OR INJURY MAY OCCUR FROM EXCESSIVE REWIND SPEED
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.baycoproducts.com
• CAUTION: Drywall will not hold the weight of the reel assembly
• CAUTION: Read and understand mounting instructions before attempting installation and
use of this product
OPERATION
• To operate, plug into a 120 Volt 60 Hz grounded outlet.
• Pull out desired length of cord. Notice a clicking noise when pulling. Cord will stay
at the desired length during clicking and rewind after a pull past the clicking noise.
Extended length when retracted can be adjusted by sliding plastic ball to desired
position.
• Move I-O switch to "I" position. Lamp may fl ash several times before lighting,
especially in cold weather. Turn off by moving switch to "O" position.
CAUTION: DO NOT ALLOW CORD TO RETRACT BY ITSELF, AS DAMAGE TO
CORD END FITTINGS MAY OCCUR FROM EXCESSIVE REWIND SPEED.
TO CLEAN OUTSIDE OF UNIT: Unplug the unit before cleaning and dry thoroughly
before re-using. Use a soft cloth with mild detergent. DO NOT use solvents such as
gasoline, turpentine, etc., to clean the unit. NEVER immerse the reel or cord end fi ttings
(receptacles or lamps) in water.
FEATURES
• 13 watt fl uorescent work light
• The cord is 20ft long; with polarized plug.
• Mounts on ceiling or wall
• Adjustable cord stop.
BULB REPLACEMENT
1. Unplug the light from the outlet.
2. Use fi ngernail or edge of knife blade to lift out plastic stud in base of lamp holder.
3. Carefully pull tube from handle.
4. Remove lamp from the lamp holder and discard.
5. Insert new lamp in socket in handle. Make sure both lamp contacts on bottom of
lamp are inserted properly into the socket.
6. Slide tube assembly over lamp and insert top of lamp into slot cut in top lamp holder.
Lamp should just penetrate slot in lamp holder.
7. Align hole in tube with hole in handle and install the plastic stud. Press in fi rmly until fully seated
MOUNTING
Ceiling or Wall Installation
1. Select a location within 18 inches of an electrical outlet. The outlet for a garage door
opener is desirable.
2. Drywall will not hold the weight of the reel assembly, so locate a ceiling joist or wall
stud and using the mounting bracket as a template, mark the holes so they are centered
on the ceiling joist or stud.
3. Attach the mounting bracket to the stud using the 2 wood screws provided.
4. Align the holes on the side of the reel with the holes in the side of the mounting
bracket and insert the pin.
5. Place the retaining ring on the pin and twist until the entire ring is through the hole in
the pin. DO NOT operate this reel without the retaining ring in place on the pin.
INS-651-19
.